FEB/27/2004 Art.Nr: 3300-6652 Kompaktalarm SX3
XCESS
SX3
Rev.1.0
www.autoalarm24.de
2
Cut the low current starter solenoid wire in the vehicle and connect one side of the cut wire to relay terminal 87A.
Connect the other side of the cut wire to relay terminal 30.
NOTE : This is a normally closed starter cut arrangement and when power is removed from the
security system, the starter disable feature will not operate, allowing the vehicle to start. We
does not recommend using the Orange wire to interrupt anything but the starting circuit of the vehicle.
6. Blue Wire: (-) Instant Trigger / Zone 2
This is an instant on ground trigger wire. It must be connected to the previously installed hood and trunk pin switches.
B. TWO-PIN WHITE & BLACK: LED Connector
Route the two wires from the previously mounted LED to the two pin connector of the module.
D. BLACK THIN WIRE - RF ANTENNA-
The black thin wire on the alarm is the receiver antenna wire. Antenna placements is very important
!
Ensure that it is
unwrapped and stretched out with the last 6" straight and keep it away from large metal objects or chassis for best
reception.
PROGRAMMING TRANSMITTER CODE:
In case the transmitter is lost, or you require additional transmitters, the code of the transmitter must be
programmed into the receiver before it is capable of responding to the new or additional transmitters. Please
perform the following procedure:
1. With the system disarmed, disconnect then reconnect power to the alarm module.
2. Within 10 seconds, turn the ignition switch on then off 6 times, ending with the key on. After 4 seconds, the siren will
chirp 3 times indicating the unit is ready to accept programming of up to 3 transmitters.
3. Within 10 seconds, press any button of the transmitter to be programmed.
NOTE:
If no transmitter button is activated, or the ignition switch is turned off, the unit will exit the program
mode. Also, any time the program mode is entered and any transmitter is activated, all other transmitters will
be erased. During the program sequence, you must have all transmitters present to be programmed that you
wish to operate and activated one at a time during the program sequence. Each transmitter activated will
cause the siren to chirp, once for the first, twice for the second and three times for the third. If a fourth is
attempted to be programmed, the first will be erased and the fourth will move the other two forward in the
program.
FEATURE PROGRAMMING
A. CHOOSING SIREN TONE -- 6 DIFFERENT SIREN TONE & MULTI SIREN TONE:
1. Within 10 seconds after disarming, press and hold
F
buttons for 3 seconds then press button of the transmitter. A
long chirp to indicate the unit is ready to accept chooses siren tone.
2. Press and release button of the transmitter to choose on a favorite tone. You can scroll through 6 different siren tones
& multi siren tone.
3. When you are satisfied with the setting, press and hold
F
button of the transmitter until the unit emits two
long chirps. This indicates the unit is locking in the adjustment.
NOTE:
If there is no transmitter activity during this mode for 10 seconds, the unit will exit the program mode and return
to the disarmed mode.
B. CHOOSING WARN AWAY SIGNALTONE -- 6 DIFFERENT WARN AWAY SIGNALTONE:
1. Within 10 seconds after disarming, press and hold
F
buttons for 3 seconds then press and release and
F
buttons
together once of the transmitter. A long chirp to indicate the unit is ready to accept chooses warns away signal tone.
2. Press and release and
F
buttons together once of the transmitter to choose on a favorite tone. You can scroll through
6 different warn away signal tones.
3. When you are satisfied with the setting, press and hold
F
button of the transmitter until the unit emits two
long chirps. This indicates the unit is locking in the adjustment.
NOTE:
If there is no transmitter activity during this mode for 10 seconds, the unit will exit the program mode and return
to the disarmed mode.
C. ADJUSTING THE SHOCK SENSOR SENSITIVITY (Zone 4):
1. Within 10 seconds after disarming, press and hold
F
buttons for 3 seconds then press button of the transmitter. A
long chirp to indicates the unit is ready to accept adjustments of the shock sensor.
2. Press and release button of the transmitter to adjust the sensitivity level. The low tone, # 1, is the most sensitive
setting, the highest tone # 8 is the least sensitive.
3. As you cycle through the tones, hit the bumper or strong metal part of the vehicle to test the threshold level of the
sensor.
Warn-Away Trigger = One chirp from siren. Shock Sensor Trigger = Two ding-dong sounds from siren.
