manualshive.com logo in svg

Xantrex PROWATT SW SW 1000, Руководство пользователя

Поделиться
Скачать
Xantrex PROWATT SW SW 1000 Скачать руководство пользователя страница 19

975-0529-01-01

9

Installation

Connect the Chassis Ground

The PROwatt SW Inverter has a screw terminal labeled CHASSIS 
GND on the outside of the rear panel as shown in Figure 3, 
“PROwatt SW Inverter Back Panel (PROwatt SW 600 shown)” on 
page 5. 
Follow the guidelines below to connect the inverter’s chassis to the 
ground.

Grounding Locations

The chassis ground terminal must be connected to a grounding 
point. The grounding point varies depending on where you install 
the PROwatt SW Inverter. Follow the guidelines that correspond to 
your type of installation.

Connect The Battery Cables

To operate safely and effectively, the PROwatt SW Inverter needs 
proper DC cables and DC-rated fuse(s). Because the PROwatt SW 
Inverter has low-voltage and high-current input, low-resistance 
wiring between the battery and the inverter is essential to deliver the 
maximum amount of usable energy to your load. 

ELECTRICAL SHOCK HAZARD

Never operate the PROwatt SW Inverter without connecting it to 
the ground.

Failure to follow these instructions will result in death or 
serious injury.

Recreational 
Vehicle

Connect the CHASSIS GND screw to the 
vehicle’s chassis using a minimum 8 AWG 
copper wire

a

 (preferably with green/yellow 

insulation).

Fixed Location

Connect the CHASSIS GND screw to your 
system’s DC grounding point using a minimum 
6 AWG wire

a

. The system’s grounding point is 

usually the AC service entrance grounding 
point or a separate ground rod. For a solar PV 
(photovoltaic) installation, this is usually the 
same rod used to ground the PV array.

a.Xantrex recommends that the grounding conductor (grounding wire) should be the same wire
size as the DC cables.

IMPORTANT:

Use of a qualified installer strongly recommended.

PROWatt SW Inverter NA.book  Page 9  Tuesday, September 14, 2010  2:29 PM

Содержание PROWATT SW SW 1000







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды