background image

Materials List

2

Freedom XC 2000 (230VAC) Owner's Guide

Materials List

The Freedom XC base package includes the following items:

n

one Freedom XC unit

n

one Owner’s Guide and extra safety labels

n

one pre-installed DC earth enclosure lug (not shown)

n

one set of plastic bushings for large DC cables

n

one bonding screw (see

Figure 6 on page 23

)

Figure 1 What’s In The Box

NOTE

: If any of the items are missing, contact Xantrex or any

authorized Xantrex dealer for replacement. See

Contact

Information on page ii

.

Key Features

Power for Most
Appliances

The Freedom XC inverter/charger provides up
to 2000 W of continuous utility grade, sine
wave power derived from a battery bank. It is
designed to handle loads such as microwave
ovens, TVs, DVD/Blu-ray players, and power
tools. In addition, the Freedom XC’s high-
surge capability lets you handle many hard-to-
start loads, including full size residential
refrigerators.

The built-in transfer switch automatically
transfers between inverter power and shore
power from recreational facilities such as boat
docks or campsites to ensure power is
always available.

Back-up
Capability

If incoming shore power is interrupted by
external events like brownouts, the Freedom
XC automatically becomes an independent
power source

1

that supplies utility grade AC

power to your loads.

1

Assuming the inverter/charger is connected to a battery source with an adequate charge at the time of the

power interruption.

Содержание Freedom XC 2000









































































































Отзывы: