background image

 

 

Pre-Wiring 

CAT-5 Wiring between MRC88m and MRKP1E 

The MRC88m and all associated components are wired using CAT-5 
terminated to the T568A or T568B Wiring Standard (Figure 2.1). When pre-
wiring the system, run lengths of CAT-5 from the pre-determined MRC88m 
location to each Keypad or Touch Panel location. The CAT-5 cable routes all 
Power, Control, Communication, and IR information needed for full system 
operation.  
 
Important: While there are two wiring standards, it is very important to be 
consistent to one configuration throughout the entire system.  Otherwise, the 
system will not operate. 
 
Note: Speaker wiring will need to be separately routed from the MRC88m to 
each zone. 

 
 

 

Figure 2.1: T568A and T568B Wiring Standard 

 

16 

USER SETUP PARAMETERS 

 

BALANCE 
Adjust audio output level on the right or left channel.   The settings can be adjusted from 
“-31” to “0” (middle) to “+31” 
 
TREBLE 
Adjust the higher frequency range of audio output. The settings can be adjusted from “-
14” to “0” (middle) to “+14” 
 
BASS 
Adjust the lower frequency range of audio output. The settings can be adjusted from “-
14” to “0” (middle) to “+14” 
 
BL COLOR 
Gives option to change the Text color and keypad backlighting to Blue or Green. 
 
GO HOME (Return to Main Setup Menu) 
After configuring the above parameters, user can choose to SAVE, NO SAVE, or 
RESTORE the settings above. 

 

INST SETUP PARAMETERS 

 

QUICK CONFIG 
Launches Xantech Quick Config. Function.  Press X” to start process.  Refer to the 
Dragon Quick Config manual for details on setting up Quick Config.  

 

KP ADDR (Keypad address) 
Assigns a different keypad address for each keypad when using multiple keypads in one 
zone

 

OLED BRIGHT (Display Brightness) 
Adjust the display brightness to DIM, MEDIUM, or BRIGHT. 
 
LED BRIGHT (Button and Volume LED Brightness) 
Adjust the button backlight brightness to DIM, MEDIUM, or BRIGHT. 

 

BL TMR VAL (Backlight Timer) 
Adjust the time when the backlight will turn off for energy savings when there is no 
activity.  Setting are “ON” (always on), “30 SEC (turns off after 30 sec), and “1 MIN” 
(turns off after 1 minute).  
 
GO HOME (Return to Main Setup Menu) 
After configuring the above parameters, user can choose to “SAVE”, “NO SAVE”, or 
“RESTORE” the settings above. 

Содержание MRKP1E













Отзывы: