background image

Federal Communication Commission Interference Statement 

This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection 
against harmful interference in a residential installation.    This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications.  However, there is no guarantee that 
interference will not occur in a particular installation.  If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one of the following measures: 
- Reorient or relocate the receiving antenna. 
- Increase the separation between the equipment and receiver. 
- Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected. 
- Consult the dealer or an experienced radio/TV technician for help. 
FCC Caution: Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate this equipment. 

Industry Canada statement: 

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject 
to the following two conditions: (1) This device may not cause harmful interference, 
and (2) this device must accept any interference received, including interference that 
may cause undesired operation. 

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux 
appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions 
suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce 
dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de 
provoquer un fonctionnement indésirable.   

IMPORTANT NOTE:   

Radiation Exposure Statement: 

This equipment complies with IC radiation exposure limits set forth for an 
uncontrolled environment. This equipment should be installed and operated with 
minimum distance 20cm between the radiator & your body. 

NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles) 
Déclaration d'exposition aux radiations: 

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies 
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un 
minimum de 20 cm de distance entre la source de rayonnement et votre corps.

 

 

Содержание PINPAD 8006L1-1CR Series






Отзывы: