background image

Avertissement: 

1) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour

une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux

systèmes de satellites mobiles utilisant les mêmes canaux;

2) Le gain maximal d’antenne permis pour les dispositifs avec antenne(s) amovible(s)

utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la imitation

P.I.R.E.;

3)

 

Le gain maximal d’antenne permis pour les dispositifs avec antenne(s) amovible(s)

 

utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour

 

l’exploitation point à point et non point à point, selon le cas.

Radiation Exposure Statement: 

This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC 

RSS-102 and had been tested in accordance with the measurement methods and 

procedures specified in IEEE 1528 and IEC 62209.  

This device and its antenna(s) must not be co-located or operating in conjunction with any 

other antenna or transmitter. 

Cet appareil est conforme aux limites d'exposition DAS incontrôlée pour la population 

générale de la norme CNR-102 d'Industrie Canada et a été testé en conformité avec les 

méthodes de mesure et procédures spécifiées dans IEEE 1528 et IEC 62209. 

Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en 

conjonction avec tout autre antenne ou transmetteur. 

Body SAR:

 

0.51

5

 

W/kg 

Содержание CL AT-170-R Series













Отзывы: