5
4
OPERATION
LOCAL
To Turn a light or appliance ON or
OFF from the keyboard.
Press and release the number button (1 -
8) corresponding to the Unit Code you
set on the Module you want to control.
Then press and release the ON or OFF
button.
To turn on ALL lights from the
keyboard.
Press and release the All Lights On button.
This turns on all lights connected to Lamp
Modules and Wall Switch Modules which
are set to the same Housecode as the Touch
Tone Controller. This button does not
affect Appliance Modules.
To turn off all lights and appliances
from the keyboard.
Press and release the All Units Off button.
This turns off all Modules which are set to
the same Housecode as the Touch Tone
Controller, including Appliance Modules.
REMOTE
1. Call home from any touch-tone phone.
If you do NOT own an answering
machine, the Touch Tone Controller
answers after 15 or 35 seconds
(depending on the position of the delay
switch) and gives three beeps. If you DO
own an answering machine it will answer
first. In this case the Touch Tone
Controller will do nothing until you enter
its PIN.
2. Enter your security code (PIN) from the
touch tone keypad on the phone you are
calling from. You hear another three
beeps.
3. Press the touch tone number key
corresponding to the X10 Module you
want to control. Use the 0 digit for
Module number 10.
4. Press * for ON or # for off. You hear 3
beeps after on, 2 beeps after off. You hear
one long beep if you press an invalid key.
You may continue to enter a number
followed by * or #. If you press 1, 2, * you
will turn on Modules 1 and 2, not Module
12. You can only control Modules 1 thru
10 from an outside phone (1 thu 8 from
the Touch Tone Controller’s keyboard).
Enter the security PIN code only once at
the beginning. If you make a mistake
when entering digits, press * or # then
enter them again. The Touch Tone
Controller keeps the line engaged for 30
seconds after the last key you press.
Slide Switch.
Set to
Min (15 secs) or Max (35
secs) answer delay.
Number keys
Security Code
(000 to 999). Last
digit sets code for
“flashing light.”
On/Off keys
All Lights On key
All Units Off key
Housecode
Set all your
Modules to the
same letter
HOW IT WORKS
Lamp
Module*
Appliance
Module*
Mini Timer*
Wall
Switch
Module*
Touch Tone Controller
The Touch Tone Controller controls lights
and appliances throughout your home from
any convenient location. It transmits signals
to X10 modules over your existing house
wiring. You plug lamps into Lamp Modules,
appliances into Appliance Modules, and
replace wall switches with Wall Switch
Modules. You can then control virtually
everything electrical in your home.
The Touch Tone Controller tells the
Modules what to do. Command signals are
sent over your existing house wiring to the
Module(s) of your choice. The Modules
respond to the signals. The Lamp Module
turns on and off any lamp up to 300 watts.
It can also be dimmed and brightened from
other types of X10 Controller. The
Appliance Module turns on and off
appliances such as a window fan, air
conditioner, or stereo, etc. It can also be used
for a lamp but can’t dim or brighten it. The
Wall Switch Module turns on and off any
incandescent light up to 500 watts. It can
also be dimmed and brightened from other
X10 controllers.
1. Plug the power cord into any functioning
120V AC outlet and plug the phone cord
into an RJ11 phone jack. (Connect to the
unit first, then to the wall jack).
2. Using a small screwdriver, set the Touch
Tone Controller’s Housecode dial to the
same letter as your X10 Modules (A
through P).
3. Set a Personal Identification Number
(PIN) (0-999). Use one, two, or three
digits as desired. Set all dials to the OFF
position for no security (PIN) code (not
recommended).
4. Set the Ans Delay switch to Min (for 15
seconds delay), or Max (for 35 seconds
delay) before the unit answers a call.
5. Install and set up X10 Modules (sold
separately). Refer to the instructions
included with the Modules.
6. Set all your Modules to the same
Housecode as you set on the Touch
Tone Controller.
7. Set each Module to a Unit Code between
1 and 8. Any Module(s) set to the same
number as the third digit on the security
code dial (on right) flashes on and off
when the phone rings.
* Sold separately
INSTALLATION