X-Rite RapidMatch GO Скачать руководство пользователя

Страница: 19 / 21

RapidMatch

GO Spectrophotometer

frozen.

and hold the power/measure

button for 10 seconds and then

release. Instrument turns off.

Instrument can be started

normally.

Measurement

error or results

appear

inaccurate.

Material being

measured is damaged

(e.g. scratched).

Repeat measurement.

Calibration was

performed on a dirty

calibration reference.

Clean the calibration reference

and repeat the calibration per

procedure in the Calibration

section.

Instrument requires

calibration.

Perform calibration on calibration

reference followed by a self test.

If calibration and self test fails,

the instrument is defective.

Contact technical support.

Instrument is defective.

Perform a self test in the Settings

menu. If the self test fails the

instrument is defective. Contact

technical support.

Calibration

procedure

fails.

Instrument defective.

Contact technical support.

Instrument and

software not

communicating

(USB

connection).

USB cable not

connected.

Connect the USB cable between

the computer and the instrument.

USB cable is defective.

Exchange USB cable.

Communication crashed

between application

software and the

instrument.

Unplug the USB cable, wait 1

second and connect the cable

again.

If the communication still does

not work, close and restart the

software application. Restart the

instrument. If the communication

still does not work, reboot the

computer.

Instrument will

not measure or

Contact sensor(s) do not

properly contact the

Lift the instrument and place it

properly on the sample. Make

Содержание RapidMatch GO






















Результаты поиска

Содержание RapidMatch GO

Отзывы:

Похожие инструкции для RapidMatch GO

Бренды по названию

Популярные бренды

X-Rite RapidMatch GO, Руководство пользователя

Результаты поиска

Содержание RapidMatch GO

Отзывы:

Похожие инструкции для RapidMatch GO

Бренды по названию

Популярные бренды