EDID Settings
EDIDs can be configured to resolve issues with video output on displays that may not accept the maximum resolution available from the source.
• When set to Smart EDID (default) the matrix will scan all selected displays for the lowest resolution to dynamically adjust the source content to allow output
on 2K and 4K displays sharing the same source.
• When EDID Copy or a direct EDID is being used, SmartEDID is turned Off.
• Ensure that a display is connected and powered On to the selected output before copying EDIDs or the copy will fail. When this occurs, EDID will be set to
4K@30Hz 2ch.
• Power to the matrix must be cycled (Off/On) after changing dip switches in order for the setting to take effect.
Accessing the Web UI
Note:
This matrix is set to a default static IP Address (192.168.11.143). In
order to communicate with it initially the PC must be set to a 192.168.11.xxx
address. This can be changed back once a static IP is set within a different
range.
1.
Connect the matrix to the same network as a PC.
2.
Open a web browser and enter the IP Address of the matrix.
Default: 192.168.11.143 | Password: admin
Note:
The installer password and general password are the same by default.
WyreStorm recommends changing the password for installer login to avoid
any unwanted changes being made to the matrix configuration.
Copying EDIDs
1.
Set the EDID dipswitch to the
Front Panel, Web UI or API EDID Control
(all switches up).
2.
Reboot the matrix.
3.
Using the front navigation buttons, select the input port for the output.
Example: Input 2 for Output 2
4.
Once the output port indicator blinks, press and hold Enter for 5
seconds. OK indicates that the copy was successful, FL-2 indicates that
the copy failed.
5.
Reboot the matrix
Note:
EDID settings may also be configured using the Web UI. Refer to the
Accessing the Web UI
section.
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is being supplied to all devices in the system and that they
are powered on.
• Verify that all source and HDBaseT connections are not loose and are
functioning properly.
• Verify that the HDBaseT cable is properly terminated per the
HDMI/
HDBaseT Wiring
section.
• Verify that the matrix, receiving device, and display support the output
resolution of the source.
• Refer to
Video Resolutions
in the
Specifications
table for the max distance
based on resolution.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
No or Intermittent 3
rd
party Device Control
• Verify that the IR cable(s) is properly terminated.
See
IR TX/RX Wiring
.
• Verify that the IR emitter is located near the IR receiver on the device.
Troubleshooting Tips:
• WyreStorm recommends using a cable tester or connecting the cable to
other devices to verify functionality.
• Use a flashlight to locate the IR receiver behind any tinted panels on the
device being control
Copyright © 2017 WyreStorm Technologies |
wyrestorm.com
MX-xxxx-HDBT-H2X Quickstart Guide | 170428
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
3 of 4
SmartEDID/Front Panel/ Web UI
4K UHD
1080p
Standard Video
Smart EDID-Display
Lowest Resolution -
2ch only (default)
4K @60Hz 2ch
No HDR
1080p @60Hz 7.1ch
1920x1200 2ch
Front Panel, Web UI or
API EDID Control
4K @30Hz 5.1ch
With HDR
1080p @60Hz 5.1ch
1920x1200 No Audio
4K @30Hz 7.1ch
With HDR
1080p @60Hz 2ch
4K @30Hz 2ch
With HDR
4K @30Hz 8bit 2ch
No HDR
