4K UHD HDCP 2.2 HDBaseT 5-Play Extender Set with 2-way PoH,
Ethernet, IR and RS-232 (4K: 70m/230ft | 1080p: 100m/328ft)
EX-70-H2X v1
Quickstart Guide
In the Box
1x EX-70-H2X Transmitter
1x EX-70-H2X Receiver
1x 12V DC 2A Power Supply (US/UK/EU)
2x 2-pin Screw Down Phoenix Connectors
2x 3-pin Screw Down Phoenix Connectors
2x Wide-band IR Emitters
2x Wide-band IR Receivers (30-50KHz)
4x Mounting Brackets (1pr for TX and 1pr for RX)
1x Quickstart Guide (this document)
Basic Wiring Diagram
HDMI
or
HDBaseT
Cat5e/6/6a
HDMI
IR Emitter
IR Emitter
IR Receiver
HDMI Source
UHD/4K Display
12 DC 2A
Power Supply
EX-70-H2X Transmitter (TX)
EX-70-H2X Receiver (RX)
IR to Control System
CAB-IR-LINK (Sold Separately)
KEY
HDMI
HDBaseT Cat5e/6
IR TX and RX
Power
IMPORTANT!
Disconnecting and connecting (hot plugging) HDMI or HDBaseT while devices
are powered on may cause damage. WyreStorm recommends powering off
devices before disconnecting these connections.
Additional Information
This Quickstart Guide provides the basic steps for the common uses of this
product. Refer to the Installation Guide and other documentation on the
product page for additional information.
Installation
Before Beginning
• WyreStorm recommends visiting the product page before installing this
product for updates to this Quickstart Guide as well as other information
about the product.
• Verify that all items are included in the packaging per the
In the Box
list.
Pre Wire
1.
Run a Cat5e/6/6a cable from the transmitter location to the receiver
location. Terminate the cable per the
HDMI/HDBaseT Wiring
section.
2.
(Optional) If using 3rd party IR emitters or connecting blocks at either
the transmitter or receiver, run the wire and terminate per the
IR TX
(Emitter) Wiring
section.
3.
(Optional) If using RS-232 pass-through, run the wire and terminate per
the
RS-232 Wiring
section.
4.
(Optional) If using 3rd party IR receivers at either the transmitter or
receiver, run the wire and terminate per the
IR RX (Receiver) Wiring
section.
Transmitter Installation
1.
Connect an HDMI source to the
HDMI In
on the transmitter using an
HDMI cable from a high quality brand such as
WyreStorm Express
.
2.
(Optional) Place an IR emitter onto the source device near the device’s
IR receiver and connect it the
IR TX
port.
3.
Connect the cable created in
Pre Wire
step 1 to the
HDBT Out
.
4.
(Optional) Connect the 3-pin connector to the
RS-232
port on the
transmitter and the opposite end to a port on a control system.
5.
If using PoH from the transmitter to power the receiver, connect the
included 18V DC 1A power supply to the
DC
12V
jack.
Receiver Installation
1.
Connect the
HDMI Out
on the receiver to an input on the display using
an HDMI cable from a high quality brand such as
WyreStorm Express
.
2.
(Optional) Place an IR emitter onto the source device near the device’s
IR receiver and connect it the
IR TX
port.
3.
Connect the cable created in
Pre Wire
step 1 to the
HDBT In
.
4.
(Optional) If using RS-232 pass-through, connect the 3-pin connector
to the
RS-232
port on the receiver and the opposite end to a port on the
device being controlled.
5.
If not using PoH to power either the transmitter or receiver, connect the
included 18V DC 1A power supply to the
18V DC 1A
jack on the either
device.
Copyright © 2016 WyreStorm Technologies |
wyrestorm.com
EX-70-H2X V1 Quickstart Guide | 161102
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Note: The following information applies to version 1 of this product as identified by v1 after the model number on the product label.
