13
We reserve the right to make changes without notice
Electronic overload protection
In case of a brief, very high overload on the product, the
integrated electronic overload protection will limit the
current consumption and in this way prevent excessive
heating of the motor.
If, when working with the product, the speed drops
significantly or the diamond cutting discs stop due to an
overload, leave the machine to run for a short time at
no-load.
In case of an extended overload, the light emitting
diode
6
will illuminate. Leave the product to run at no-
load until the motor has cooled to its normal operating
temperature and the light emitting diode
6
goes out.
Restart protection
If the plug is connected to the mains with the product
switched on or the supply of power is re-established
after a power failure, the product will not start. The
light emitting diode
6
flashes and the product must be
switched off and on.
Maintenance and care
q
Unplug from the mains before all work on the
product.
Always keep product and ventilation slots
clean.
To prevent dust building up inside the product, the motor
must be blown out after extended use of the product
(through the ventilation slots on the rear end of the motor
housing). This task should not be undertaken indoors if
possible.
Should, despite careful manufacturing procedures and
test procedures, the product fail at some point, have
the product repaired by an authorised customer service
centre for WÜRTH electrical tools.
It is imperative you state the article number (see type
plate) of the product with all queries and orders for
spare parts..
Spare parts
It is only allowed to use original spare parts. The use of
other parts can cause damage to the product.
Protecting the environment
Recycling instead of refuse disposal.
Products, accessories and packaging
that are no longer useable should be
sent for recycling.
Only in EU countries:
Do not throw electrical tools in household waste. In
accordance with European directive 2002/96/EC
on waste electrical and electronic equipment and its
implementation in national law, used electrical tools
must be collected separately and recycled.
Warranty
For this WÜRTH product we provide a warranty as per
legal / national stipulations from the date of purchase
(proof of purchase with invoice or delivery note).
Resulting damage will be rectified by replacement or
repair. Damage due to improper handling is excluded
from the warranty.
Complaints can only be accepted if the product is
returned, without dismantling, to a WÜRTH subsidiary,
your WÜRTH sales representative or a service centre for
electrical tools authorised by WÜRTH.
Declaration of conformity
We herewith declare that this product conforms with the
following standards and directives:
Technical documentation with:
Standards
• EN 60745-1:2009 + A11:2010
• EN 60745-2-22:2011 + A11:2013
• EN 55014-1:2006 + A1:2009 + A2:2011
• EN 55014-2:1997 + A1:2001 + A2:2008
• EN 61000-3-2:2006 + A1:2009 + A2:2009
• EN 61000-3-3:2008
• EN 50581:2012
in accordance with the regulations stipulated in the
directives:
EC directive
• 2006/95/EG
• 2014/30/EU
• 2011/65/EU
Adolf Würth GmbH & Co. KG, Abt. PPT
Reinhold-Würth-Straße 12 – 17,
74653 Künzelsau, GERMANY
F. Wolpert
Dr.-Ing. S. Beichter
Authorized Signatory,
Head of Product Ma-
nagement
Head of Quality,
Authorized Signatory
Künzelsau: 16.06.2016
Содержание MSF 30
