wtw pHotoFlex STD Скачать руководство пользователя страница 60

Страница: 60 / 80

Maintenance, cleaning, disposal

pHotoFlex

STD

ba75958e07

11/2020

Maintenance, cleaning, disposal

5.1

Maintenance

The meter is almost maintenance-free.
The only maintenance task is replacing the batteries or battery pack.

5.1.1

Inserting/exchanging the batteries

NOTE

Make sure that the poles of the batteries are positioned correctly.
The ± signs on the batteries must correspond to the ± signs in the battery
compartment.

Open the battery compartment:

– Unscrew the two screws (1) on the underside of the meter,

– Remove the lid of the battery compartment (2).

If necessary, take four old batteries out of the battery compartment.

Insert four batteries (3) in the battery compartment.

Close the battery compartment and fix it with the screws.

Содержание pHotoFlex STD
















































































Результаты поиска

Содержание pHotoFlex STD

Отзывы:

Похожие инструкции для pHotoFlex STD

Бренды по названию

Популярные бренды

wtw pHotoFlex STD, Руководство пользователя

Результаты поиска

Содержание pHotoFlex STD

Отзывы:

Похожие инструкции для pHotoFlex STD

Бренды по названию

Популярные бренды