wsm m9540 Скачать руководство пользователя | Manualshive

Страница: 34 / 73

background image

L3-S7

M9540Low Profile, WSM

TRANSMISSION

[2] ROPS

ROPS Upper Frame

1. Hook the upper frame (1).
2. Remove the damper mounting nut (2).
3. Remove the lunch pin (5) and set bolt (4).
4. Remove the upper frame (1) using a hoist.
5. Remove the external position control rod (6).
6. Remove the lift rod (7) and lower link (8).

W1012812

Rear Wheel and Front Axle Rocking Restrictor

1. Place the disassembling stand under the transmission case.
2. Install the front axle rocking restrictor (1). (Refer to “8. SPECIAL

TOOLS” at “G.GENERAL” section.)

3. Remove the rear wheel.

(When reassembling)

W1012997

(1) Upper Frame
(2) Nut
(3) Damper
(4) Set Bolt

(5) Lynch Pin
(6) External Position Control Rod
(7) Lift Rod
(8) Lower Link

Tightening torque

Rear wheel mounting nut

343.2 to 393.3 N·m
35.0 to 40.1 kgf·m
253.2 to 290.0 lbf·ft

(1) Front Axle Rocking Restrictor

KiSC issued 09, 2008 A

«
...
32
33
34
35
36
...
»

Содержание m9540










































































Отзывы:

Нет отзывов

Похожие инструкции для m9540

Бренд: Terex Страницы: 116

Бренд: Kersten Страницы: 19

Бренд: Ariens Страницы: 30

Бренд: Wheel Horse Страницы: 11

Бренд: Hagie Страницы: 102

Бренд: Hagie Страницы: 120

Бренд: Valtra Страницы: 41

Бренд: Valtra Страницы: 11

Бренд: Vari Страницы: 9

Бренд: Pasquali Страницы: 65

Бренд: Captain Страницы: 121

Бренд: Zetor Страницы: 41

Бренд: TILMOR Страницы: 28

Бренд: TILMOR Страницы: 29

TeeJet Matrix 908

Бренд: Spraying Systems Страницы: 40

Бренд: Poettinger Страницы: 55

Бренд: NPK Страницы: 29

Бренд: MTW Страницы: 188

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды