Wright Manufacturing Stander ZK Скачать руководство пользователя страница 8

 

  Before attempting to start the engine, follow all 

starting instructions below and in the 
engine operator’s manual. 

  Look behind before backing up. 

  Before leaving the operator’s position, even  

momentarily, turn off the blade clutch 
engagement switch and apply the parking 
brake.  Keep others from coming near the 
mower.  Get back on the mower as soon 
as possible. 

  When leaving the Wright mower unattended, 

turn off the blade clutch engagement 
switch, apply the parking brake, stop the 
engine and remove the key.  Never leave 
the machine unattended on a slope in 
case someone disengages the parking 
brake which would be hazardous if the 
mower were to roll. 

  When transporting, driving onto transport 

vehicles, into buildings, across parking 
lots or otherwise not mowing grass, turn 
off the blade clutch engagement switch to 
reduce risk of thrown objects and rotating 
blade hazard.  After coming to a stop 
apply the parking brake, stop the engine 
and remove the key. 

  Before performing any maintenance or repair 

service, disengage power to blades, apply 
the parking brake, stop the engine, 
remove ignition key and spark plug wire 
from spark plug(s). 

  All operators of this mower should exercise 

caution when driving this mower at high 
speeds.  Sudden stops from excessive 
speeds may cause serious injury. 

  DO NOT allow inexperienced people to 

operate the mower until they have read 
and understood these safety instructions.  
Operate the mower at slower speeds 
while becoming familiar with it.
 

  The grass discharge chute deflector must be 

installed at all times and in the down 
position except that it may be raised when 
the grass catcher is completely installed or 
a mulch kit is completely installed. 

  If the mower discharge clogs, turn off the 

blade clutch switch, apply the parking 
brake, stop the engine and remove the 
key before removing obstruction. 

  Keep all shields and covers in place, 

especially grass discharge chute deflector 
and the blade belt covers. 

  Keep hands, feet and clothing away from 

rotating parts, especially the rear wheels, 
blades, engine flywheel, belts and pulleys. 

  Do not touch engine or muffler while engine is 

running or soon after it is stopped.  These 
areas can be so hot as to cause severe 
burns. 

  Clean grass, leaves and lubricant spills 

from surfaces after use to prevent fire 
hazard.
 

  Be alert for traffic when crossing roads or 

operating near roadways. 

  Before climbing curbs, crossing gravel drives, 

sidewalks or roads, turn off the blades, lift 
them into transport position, and wait for 
them to stop. 

 

 

 

 

Operation In Forward Direction 

Always keep a firm grip on the mower stationary 
handlebar with both hands.  Operate the mower 
slowly until you become familiar with how the 
mower operates.  Do not operate the mower 
faster than conditions allow.  For example, hills, 
wet or bumpy ground, dim light or high grass are 
all conditions requiring slower speeds.  Never 
operate the mower at the highest speed unless 
you are on level, wide, open areas of clearly 
visible ground or transporting on paved areas. 
Speeding with any mower is dangerous, and so 
is traveling faster than conditions should permit 
on this mower.  Sudden stops from excessive 
speed or falling off the mower may cause 
serious injury or death. 

 
 
 
   

 

Operation In Reverse 

Always keep a firm grip on the mower stationary 
handlebar with both hands.  Keep both feet 
firmly on the foot platform.  Look behind you 
before backing to prevent injuring yourself or 
anyone behind you.  Operate the mower very 
slowly, inching it backward until you become 
familiar with how the mower operates.  Always 
operate slowly if in an awkward location or 
position.  While backing up, never place your 
foot or feet on the ground near the back edge of 
the mower to prevent serious personal injury if 
the mower were to run over you.   
 

 
 

Zero-Radius Turn Operation 

During zero-radius turns (when one mower 
wheel rotates backwards while the other rotates 
forward) drive extra slowly to reduce the 
possibility of losing traction, or control, or 
becoming dizzy.  This will help prevent you from 
being thrown off the mower.  Be aware that if 
you do a turn on a slope you may go through all 
of the orientations to a slope mentioned below 
and must handle the mower accordingly. 

 
 

    

WARNING 

    

WARNING 

    

WARNING 

Содержание Stander ZK

























Отзывы: