background image

Wren 44 TurboProp Users Manual.  Copyright  Wren Turbines Ltd February 2008        Page  28 

The display should now change to: 

 
 
 
 
 

Leaving  the  throttle  stick  in  the  minimum  position,  raise  the 
throttle trim to the full up position or switch “Engine Cut” switch 
to off, and again press the right (+) button. 
 
If you have done all steps correctly a blue LED will light up in 
the end of the ecu under the display plug, and the display will 
change to: 

  
 
 
 

 
NB. The value for acceleration delay may be set other than shown – do not alter it. 
 
Lower  your  throttle  trim  and  the  green light should  turn  off or  go  very  dim.  If  it  does not then  you  need  to 

reverse the throttle channel,

 and repeat the radio set-up.  

 
This  completes  your  radio  setup  and  should  only  need  doing  again  if  the  radio  settings  are  changed 
significantly or if you suspect the setup to have altered.  
 
You  will  note  there  are  many  settings,  which  can  be  adjusted  in  the  ECU.  Please  resist the  temptation  to 
change things as firstly this is unnecessary as they are preset for optimum performance of your engine, and 
secondly you may change something which will adversely affect the starting and running of the engine.

 

 
Running Time Counter. 

 
Using the 2nd left hand button (v), scroll through the menu’s to the last menu. 

 

 
 
 
 
 

The screen contains a timer which shows: 
 
the total running time of the engine in minutes (Tot), 
the time in seconds of the last engine run (Last) 
the total number of starts (cycles - CY) . 
 

Use this screen to keep track of your total running time and starts. 
 

Basic ECU Settings 

These are the 

initial

 settings used in setting up the ECU to the engine. These are then optimised to suit each 

engine. Do not change the values present in your ecu without referring back to Wren Turbines. 

 
Max rpm

  

 

–  

195,000rpm. 

Idle rpm

   

 

–  

55,000rpm. 

Stop rpm

  

 

–  

32,000rpm. 

Start temp’

  

 

–  

100’C. 

Max temp’ 

 

– 

848’C. 

Acceleration delay  

–  

5-10. 

Deceleration delay

  

– 

10-30 

Stability Delay

 

 

–  

50. 

Pump start point

    

–  

Auto+1. 

Pump Start Ramp 

 – 

 

006. 

Glow plug power

   

– 

32-36 

Stick Down

Stick Down

Stick Down

Stick Down 

 

 

 

Trim Up

Trim Up

Trim Up

Trim Up 

 

 

   

 

 

 

(Idle)

(Idle)

(Idle)

(Idle)

 

Acceleration

Acceleration

Acceleration

Acceleration 

 

 

 

Delay 005

Delay 005

Delay 005

Delay 005 

 

 

 

Timer:  

Timer:  

Timer:  

Timer:   

 

 

     Tot:0000m    

   Tot:0000m    

   Tot:0000m    

   Tot:0000m    

Last: 000s

Last: 000s

Last: 000s

Last: 000s 

 

 

 

 Cy:000

 Cy:000

 Cy:000

 Cy:000 

 

 

 

Содержание 44 TurboProp





































Отзывы: