WPI INV-101 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 32

background image

INV-101

WORLD PRECISION INSTRUMENTS

3

MICROSCOPE SETUP

Before setting up the microscope, carefully open the box and inspect its contents. The
pieces of the microscope are stored in two Styrofoam containers, and many of the
pieces are wrapped in plastic (

Fig. 2

). Carefully unwrap each piece before setting up the

instrument. The following instructions graphically show how to setup your inverted
microscope.

NOTE

: If you have a problem/issue that falls outside the definitions of this manual,

contact the WPI Technical Support team at 941.371.1003 or technicalsupport@wpiinc.
com.

Setting up the Base and Stage

1. Remove the base of the microscope and set it up on a firm tabletop surface (

Fig. 3

).

Fig. 4

shows the back of the microscope base. The A/C power plug adapter, the serial

number and the fuse compartment are located on the back.

Fig. 5

shows the power

switch and lamp brightness control located on the side of the microscope.

Condenser Mount

Lamp Connector

Head Mount

Stage

5-Position Nosepiece

Focus Control Knob

Front

Back

Fig. 3–Base of the microscope.

«
...
5
6
7
8
9
...
»

Содержание INV-101

































Отзывы:

Нет отзывов

Похожие инструкции для INV-101

BH2-CH Substage

Бренд: Olympus Страницы: 26

Бренд: insize Страницы: 8

Бренд: AmScope Страницы: 19

Бренд: AmScope Страницы: 17

Бренд: AmScope Страницы: 20

Бренд: Nikon Страницы: 26

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 12

Бренд: Califone Страницы: 7

Бренд: symbio Страницы: 11

1820 Series BIOSTAR

Бренд: Reichert-Jung Страницы: 13

MicroXplore 51856

Бренд: OPTRONIC Страницы: 8

Бренд: TROIKA Страницы: 34

Бренд: LW Scientific Страницы: 1

Бренд: LW Scientific Страницы: 1

Student Scope OEM-SF3

Бренд: LW Scientific Страницы: 1

Бренд: LW Scientific Страницы: 1

Revelation III LED

Бренд: LW Scientific Страницы: 4

Бренд: Thermo Scientific Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды