–– Function Menu Options & Descriptions 54–62
Visit
for more information or support,
to download a printable PDF version of this manual or the original pre-
programmed HAM SHTF Channel Chart, the original KG-UV9P
manual (for advanced features), or the free
WOUXUN
Customer
Programming Software and USB Programming Cable software
drivers, to purchase a host of useful accessories such as a high-gain
HAM-tuned
Smiley Antenna
to extend your operating range, or to post
a gear review & provide constructive feedback, which are always
welcome and appreciated.
When the SHTF, BetterSafeRadio than Sorry!
™
54
AM-SW
AM Receive Mode Switch
OFF
|
ON
(OFF = Normal FM Mode RX)
Disable or enable AM Mode RX on current memory channel.
55
PF1–DEF
SP
Prog. Function Key 1 Short
OFF
|
CALLID
|
R–ALARM
SOS
|
SF–TX
(
italic
is default)
56
PF2–DEF
LP
Prog. Function Key 2 Long
OFF
|
SCN
|
SECOND
LAMP
|
SDF–DIR
K–LAMP
57
PF3–DEF
LP
Prog. Function Key 3 Long
OFF
|
CALLID
|
R–ALARM
SOS
|
SF–TX
|
SCN
SECOND
|
LAMP
58
VOLTAGE
Battery DC Volts
SHOW
|
HIDE
Press MENU to show (for 12 sec.) or hide battery voltage.
59
QT–SW
Quiet Tone Scan Switch
OFF
|
ON
(ON uses CTC/DCS stored in each channel)
Enable CTCSS/DCS speaker muting while scanning.
60
S–MUTE
Sub-Receiver Mute Mode
OFF
|
RX–MUTE
|
TX–MUTE
|
R/T–MUTE
Mute alternate receiver during RX, TX, or both, on
MAIN
rec
.
61
RESET
Name
VFO
|
ALL
(Menu Functions | Menu & Memories
–
BEWARE!
)
ALL
restores radio to 29-channel HAM/NOAA configuration.
62
SCN–MD
Color Screen Mode
Classic
|
Covert
|
Day 1
|
Day 2
Set color Screen Modes. Radio will power-cycle on change.
–– Function Menu Options & Descriptions 34–53
© Copyright 2022 BetterSafeRadio –
All Rights Reserved – v1.07
–– Function Menu Options & Descriptions 01–17
–– Function Menu Options & Descriptions 18–33
01
ABR:s
Auto Backlight Timer
OFF
|
1
S–
30
S |
ALWAYS ON
| (in seconds)
Duration LCD backlight remains on after any activity.
02
SAVE
Battery Power Saver
OFF
|
1
–
4
(1=2:4, 2=2:6, 3=2:8, 4=3:9 – in 100mS)
Receiver duty-cycling to save battery life. 4 cust. in software.
03
STEP
Tuning Step
2
.
5
K |
5
K |
6
.
25
K |
8
|
10
K |
12.5
K |
20
K |
25
K |
30
K |
50
K |
100
K
Tuning step for FREQ-VFO Display Mode in kHz.
04
W/N
Modulation Bandwidth
WIDE
|
NARR
(16 kHz | 11 kHz)
RX/TX modulation bandwidth for 25k / 12.5k channels.
05
TXP
Transmit Power
LOW
|
MIDDLE
|
HIGH
(2 Watts | 5 Watts | 8+ Watts)
RF output power level for TX (transmit).
06
SFT–D
TX Shift Direction
OFF
|
+
|
–
(only in FREQ-VFO Mode)
TX frequency o
ff
set direction for repeater operation.
07
VOX
Voice-Operated Transmit
OFF
|
01
–
10
(01 is highest sensitivity)
Sensitivity for automatic TX based on microphone voice level.
08
SQL–LE
Squelch
0
–
09
(0 = OFF/OPEN)
Signal strength threshold for squelch speaker muting.
09
ROGER
Roger Beep
OFF
|
BOT
|
EOT
|
BOTH
(B = Beginning, E = End Of TX)
Courtesy “OVER” tone during TX. Not typical on repeaters.
10
TOT:s
Time-Out Timer
15
S–
180
S (in 15 second increments)
Timer for automatic TX shuto
ff
to protect transmitter.
11
TOA:s
Time-Out Timer Alarm
OFF
|
01
S–
10
S (in seconds)
LED warning flashing time before TOT expires.
12
VOICE–SW
Voice Announce/Prompt
OFF
|
ON
Voice announcements/prompts.
13
BEEP
Key Beep
ON
|
OFF
Audible keypad & function key confirmation tone.
14
MENULANGE
Menu Language
Disabled. Always set to ENGLISH.
15
BCL
Busy Channel Lockout
OFF
|
ON
TX inhibit when active signal detected on channel/freq.
16
Rx–CTC
Cont. Tone-Coded Squelch
OFF
|
67
.
0
Hz–
254
.
1
Hz (or non-standard values via keypad)
RX CTCSS “PL/Quiet Tone” decoding for speaker muting.
17
Tx–CTC
Cont. Tone-Coded Squelch
OFF
|
67
.
0
Hz–
254
.
1
Hz (or non-standard values via keypad)
TX CTCSS “PL/Quiet Tone” encoding during transmit.
18
Rx–DCS
Digital-Coded Squelch
OFF
|
D023N/I
–
D754N/I
(Press
#
to toggle DCS polarity)
RX (receive) DCS “DPL” decoding for speaker muting.
19
Tx–DCS
Digital-Coded Squelch
OFF
|
D023N/I
–
D754N/I
(Press
#
to toggle DCS polarity)
TX DCS “DPL” encoding during transmit.
20
SC–REV
Scan Review
TO
|
CO
|
SE
(Timer | Carrier | Search)
Signal detection/monitor behavior while scanning.
21
SP–MUTE
Speaker Muting
QT
|
QT
✱
DT
|
QT&DT
(Quiet Tone | QT or ANI | QT & ANI)
Require Quiet Tone and/or ANI–ID to unmute speaker.
22
DTMF–ST
DTMF & ANI Side-Tones
OFF
|
DT–ST
|
ANI–ST | DT
+
ANI
(DTMF | ANI-ID | Both)
Enable hearing DTMF keypad and/or ANI–ID tones during TX.
23
PTT–ID
Transmit Unit ID #
OFF
|
BOT
|
EOT
|
BOTH
(B = Beginning, E = End)
Send your ANI-ID (Unit #) during TX with PTT (Push-To-Talk).
24
ID–EDIT
Unit Identification
0
–
9
(ANI-ID up to 6 digits, 3-digit min., use keypad to enter)
Automatic Number Identification (Unit #) for Selective Calling.
25
ID–DLY:ms
Identification TX Delay
100
MS–
3000
MS (in milliseconds)
Delay before ANI-ID is sent after TX starts, with PTT-ID.
26
RING:s
Incoming Select Call Ringer
OFF
|
01
S–
10
S (in seconds)
Duration of audible ringer before voice, when RX ANI-ID.
27
ABR–LV
Automatic Backlight Level
01
–
05
(05 is highest brightness)
Brightness for automatic LCD backlight.
28
OFFSET
TX O
ff
set Frequency
0
–
999.99750
(in MHz, Ex. 000.60000 MHz used on 2 meters)
TX o
ff
set freq. for repeater operation. (only FREQ-VFO Mode)
29
CH–NAME
Channel Alpha-8 Name
! ” # $ % & ’ ( ) * + , – . / 0
–
9 : ; < = > ? @ A
–
Z [ \ ] ^ _ ` a
–
z { | } ~
Enter up to 8 char.,
#-LOCK
=
right,
EXIT
=left,
LP
EXIT
=exit
30
MEM–CH
Save Memory Channel
001
–
999
(3 digits,
MENU
=write,
EXIT
=cancel)
Write current settings to any used/unused memory channel.
31
DEL–CH
Delete Memory Channel
001
–
999
(3 digits,
MENU
=erase,
EXIT
=cancel)
Erase any used memory channel.
32
PRI-CH
Priority Channel
001
–
999
(3 digits,
MENU
=set,
EXIT
=cancel)
Set any used memory channel as the Priority Channel.
33
PRI–SCN
Priority Channel Scan
ON
|
OFF
Enable Priority Scanning (of the Priority Channel in standby).
34
AUTOLOCK
Auto-Lock
OFF
|
ON
Enables LOCK mode after 15 seconds of no activity.
35
LOCKMODE
Lock Mode
KEY–LK
|
KEY
+
PG
|
KEY
+
PTT
|
ALL
PF keys, or + Ch. Knob, or + PTT (RX-only), or all.
36
S–TONE
Single-Tone TX “Tone-Burst”
1000H
|
1450H
|
1750H
|
12100H
(in Hz, press
PF3
while TX)
Frequency of Single-Tone TX (for repeater access).
37
VOX–DLY:s
VOX Transmit Delay
OFF
|
01
S–
05
S (in seconds)
Duration TX continues after microphone audio/voice stops.
38
SC–QT
Save Coded Quiet Tone
R–QT
|
T–QT
|
R&T–QT
(RX–CTC/DCS | TX | Both)
Where found CTC/DCS tone is saved after
SCN–CD
search.
39
APO–TMR
Auto-Power-O
ff
Timer
OFF
|
15
M–
150
M (in 15 minute increment)
Timer for auto power o
ff
if no keypad or channel knob use.
40
PONMSG
Power-On Message
BATTY
|
BITMAP
(BITMAP only active if factory image set)
Battery DC Volts or custom image during radio power-up.
41
BLCDSW
Backlight LCD Switch
OFF
|
ON
Dims LCD backlight instead of turning o
ff
completely.
42
BLEDSW
Backlight LED Switch
OFF
|
ON
Flashes status LED when LCD is o
ff
to indicate radio is on.
– –
MENU 43–47
See KG-UV9P manual PDF for Cross-Band Repeater use.
48
SCN–ADD
Scan Add Channel
OFF
|
ON
Disable or enable scanning of currently selected channel.
49
SCN–GP
Scan Group
01:name
–
10:name
|
ALL
(Scan Groups set via software)
Set active Scan Group, or all channels, for each receiver.
50
SCN–MODE
Scan Range Mode
ALL
|
Cur Region
|
Lmt Frq
(Limit Freqs. set via software)
Limit FREQ-VFO scanning to all, current band, or limit freqs.
51
SCN–CD
Scan CTCSS/DCS
CTCSS
|
DCS
(Use
Ch. Knob
or
▲▼
to change scan dir.)
Scan for CTCSS or DCS tone/code on active signals.
52
CALL ID
Select Call ID
01:name
–
20:name
(Call ID Group Names set via software)
Select Calling ID (Group) to TX (if CALL enabled on a PF key).
53
AUTO–AM
Auto-AM Receiver Mode
OFF
|
ON
(Activates AM Mode when AM signal detected)
Disable or enable automatic AM Mode detection switch.
CALLID: TX Group ID Call
R–ALARM: TX Remote Siren
SOS: Local Emergency Siren
SF–TX: Alternate Rec. PTT
SCN: Toggle Scan Mode
SECOND: Toggle Stopwatch
LAMP: Toggle Flashlight
SDF–DIR: Toggle O
ff
set Dir.
K–LAMP: Toggle Backlight
