background image

3

2

GENERAL POwER TOOL SAFETY wARNINGS

WARNING: Read all safety warnings and 

instructions.

 Failure to follow the warnings 

and instructions may result in electric shock, fire 

and/or serious injury. 

Save all warnings and instructions for future 

reference.

The term power tool in the warnings refers to your 

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1)  

 

WoRk AReA SAfety

a)   keep work area clean and well lit.

 Cluttered 

or dark areas invite accidents.

b)   Do not operate power tools in explosive 

atmospheres, such as in the presence of 

flammable liquids, gases or dust.

 Power 

tools create sparks which may ignite the dust or 

fumes.

c)   keep children and bystanders away while 

operating a power tool.

 Distractions can 

cause you to lose control.

2)   electRIcAl SAfety

a)   Power tool plugs must match the outlet. 

Never modify the plug in any way. Do 

not use any adapter plugs with grounded 

power tools.

 Unmodified plugs and matching 

outlets will reduce risk of electric shock.

b)   Avoid body contact with grounded 

surfaces such as pipes, radiators, ranges 

and refrigerators.

 There is an increased risk 

of electric shock if your body is earthed or 

grounded.

c)   Do not expose power tools to rain or wet 

conditions.

 Water entering a power tool will 

increase the risk of electric shock.

d)   Do not abuse the cord. Never use the 

cord for carrying, pulling or unplugging 

the power tool. keep cord away from 

heat, oil, sharp edges or moving parts.

 

Damaged or entangled cords increase the risk 

of electric shock.

e)   When operating a power tool outdoors, 

use an extension cord suitable for outdoor 

use.

 

Use of a cord suitable for outdoor use 

reduces the risk of electric shock.

 

f

 

)   If operating a power tool in a damp 

location is unavoidable, use a Ground 

fault circuit Interupter (GfcI) protected 

supply.

 Use of a GFCI reduces the risk of 

electric shock.

3)  PeRSoNAl SAfety

a)   Stay alert, watch what you are doing 

and use common sense when operating 

a power tool. Do not use a power tool 

while you are tired or under the influence 

Содержание WX254

















Отзывы: