40V Cordless Lawn Mower
EN
17
Note:
1. Be sure the mower is turned off and remove
the key.
2. Place the mower in stand up storage mode.
TO SHARPEN BLADE IN A VISE (SEE Fig. O1)
1. Be sure the switch lever is released, the blade
has stopped and the safety key removed before
removing the blade.
2. Remove blade from mower. See instructions
for removing and attaching blade.
3. Secure blade O1-1 in a vise O2-2.
4. Wear safety glasses and be careful not to cut
yourself.
5. Carefully file the cutting edges of the blade
with a fine tooth file O3-3 or sharpening stone.
6. Check balance of blade. See instructions for
blade balancing.
7. Replace blade on mower and tighten securely.
Refer to instructions below.
BLADE BALANCING (SEE Fig. O2)
Check balance of blade by placing center hole in
blade O2-1 over a nail or screwdriver shank O2-2,
clamped horizontally in a vise O2-3. If either end of
the blade rotates downward, file that end. Blade is
properly balanced when neither end drops.
BLADE MAINTENANCE (See Fig. P1, P2)
Renew your metal blade after 50 hours mowing
or 2 years, which ever is the sooner-regardless of
condition.
Follow these procedures to remove and replace the
blade. You will need garden gloves (not provided)
and a spanner wrench (not provided) to remove
the blade. Hold the blade and unscrew the blade
bolt counter-clockwise using a spanner wrench, and
then remove blade.
To re-assemble, position the blade with the cutting
edges towards the ground. Then securely tighten
the blade bolt.
STORAGE (SEE Fig. N1, N2)
Stop the mower and always remove the safety key.
Clean the exterior of the machine thoroughly using
a soft brush and cloth. Do not use water, solvents
or polishes. Remove all grass and debris, especially
from the ventilation slots.
Turn the machine on its side and clean the blade
area. If grass cuttings are compacted in the blade
area, remove with a wooden or plastic implement.
Store the machine in a dry place. Do not place other
objects on top of the machine.
To aid storage, release the Lock Cam Lever, and fold
the upper handle as shown in Fig. N1, N2.
CUTTING AREA
The cutting area can be affected by many factors
including: cutting height, operation practices (ex:
starting/stopping), lawn moisture levels, grass
length and thickness.
The below table provides the potential cutting areas
based on specific cutting conditions.
Cutting
Height
Recommend lot size (maximum)
Cutting
off .75”
(2cm)
With 2*40V/2.0Ah batteries
Up to 5500 sq. ft.*
* Used with two fully charged battery packs.
TIPS:
1) Mowing the lawn frequently and reducing
the amount of starting/stopping procedures
will help conserve battery runtime. It is
recommended to always use the same two
batteries during operation with fully charged
levels.
2) For the best cutting performance, it is
recommended to only mow up to 1/3 or less
of the current grass height at a time. Mow at
a slower pace when cutting long/thick grass
to allow the mower to properly discharge the
clippings.
Содержание WG750
