3-in-1 Lawn mower
en
15
14
15
14
recoMMended cuttng height
Mowing tipS
note: always inspect area where mower
is to be used and remove all stones,
sticks, wire, metal and other debris
which might be thrown by the rotating
blade.
1. Mow across the face of slopes, never up-
and-down. Exercise extreme caution when
changing direction on slopes. Do not mow
excessively steep slopes. Always maintain
good footing.
2. Release switch lever to turn mower “OFF”
when crossing any graveled area (stones
can be thrown by the blade).
3. Set mower at highest cutting height when
mowing in rough ground or in tall weeds.
Removing too much grass at one time can
cause circuit breaker to trip, which stops
mower.
4. If a grass collection bag is used during the
fast growing season, the grass may tend to
clog up at the discharge opening. Release
switch lever to turn mower “OFF”. Remove
the grass collection bag and shake the
grass down to the back end of the bag.
Also clean out any grass or debris which
may be packed around the discharge
opening. Replace the grass collection bag.
5. If mower should start to vibrate
abnormally, release switch lever to turn
mower “OFF”. Check immediately for
cause. vibration is a warning of trouble. Do
not operate mower until a service check
has been made.
alwayS releaSe Switch lever to
turn Mower “off”.
Mulching Mowing tipS
While mulching, your new mower is designed
to cut the grass clippings into small pieces
and distribute them back into the lawn. Under
normal conditions, the mulched grasses will
biodegrade quickly to provide nutrients to the
lawn.
Please review the following recommendations
for optimum mulching performance.
1. Avoid mowing when the grass is wet from
rain or dew. Wet grass may form clumps
which interfere with the mulching action
and reduce runtime. The best time to mow
grass is in the late afternoon when the
grass is dry and the newly cut area will not
be exposed to direct sunlight.
2. For best mulching performance, set
the cutting height to remove about one
third of the grass blade length, ideally
no more than 1-1/2” at one time. If the
lawn is overgrown, it may be necessary
to increase the cut height to reduce the
pushing effort and prevent overloading the
motor. For extremely heavy mulching, it is
advisable to first cut at a high cut height
setting, and then re-cut to the final cut
height. Otherwise, make narrower cuts and
mow slowly. (See I)
3. For best performance, keep the mower
housing free of built-up grass. From time
to time turn off mower and wait for the
blade to come to a complete stop. Using
an object such as a stick, wipe out any
accumulation of grass in the blade area.
Be careful of the sharp edges of the blade.
Clean often in wet, new grass, and always
Type
Cut Height
Range
BAHIA
2”-3”
BERMUDA
1/2”-1”
BUFFALO
1-1/2”-2-1/2”
CARPET
1”-2”
CENTIPEDE
1”-2”
ST.AUGUSTINE
2”-3”
ZOYSIA GRASS
1/2”-1”
CREEPING BENT GRASS 1-1/3-2/3”
vELCER BENT GRASS
1/4”-1/2”
ANNUAL BLUEGRSS
1/2”-1”
CANADA BLUEGRASS
3”-4”
kENTUCkY BLUEGRESS 2-1/2”-3”
ROUGH BLUEGRASS
1”-1-1/2”
FINEFESCUE
1-1/2”-2-1/2”
TALLFESCUE
2-1/2”-4”
ANNUALRYEGRASS
2”-2-1/2”
Содержание WG71 8
Страница 2: ...3 9 8 7 6 5 4 1 2...
Страница 3: ...b 1 2 3 1 3 1 2 3 a 1 10 11 1 2 A B1 B2 B3 C D1 D2 E F G1 G2 H I J K...
Страница 4: ...6 M 1 M 2 M 3 L 1 L 2 L 3 L M N...