11
10
10
Electric Pressure Washer
EN
Cleaning
Begin with the nozzle 1-2ft away
from the surface and approach
with caution until it reaches the
desired position for overly close
spray may do harm to surface.
WARNING
: Do not
connect the machine to
water supplies that are
dirty, rusty, muddy, or corrosive.
(Including window cleaning
liquids, plant foods, or fertilizers
etc.)
See Fig. J
Add and use detergent
Install the soap nozzle before
operation.
Note:
If necessary, use a funnel
(not supplied)to prevent ac-
cidental overflows of detergent
outside of the tank.
See Fig. K1, K2, K3
MAINTENANCE
Remove plug from the socket before carrying out
any adjustment, servicing or maintenance.
Inspect the product for damaged or worn parts before each
use. Do not operate it if you find damaged or worn parts.
Contact your supplier or the manufacturer for replacement
parts.
Power cord maintenance
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard
Pump maintenance
Inspect the pump frequently whether any leaking occurs
around the pump seal. If leaking occurs, please contact
service center for repair.
Nozzle maintenance
Remove the nozzle from the lance, then remove any
possible obstructions using the included declogging needle
(See Fig. L).Then use a garden hose to rinse the nozzle by
backwashing
WARNING
: Any other servicing should be performed
by an authorized service representative.
STORAGE
1. Disconnect the water source. Turn on the pressure
washers for a few seconds until the remaining water
flows out. Then turn it off quickly.
2. Unplug the power supply and wind power cord on the
lance holder. (See Fig.M)
3. Disconnect the high pressure hose and the garden hose
(not supplied) .Then wind high pressure hose on the
tool. Insert the Wand and lance separately into the Wand
Holder and lance holder. (See Fig. M)
4. Store in a frost free area with a temperature above
0°C(32°F).
TROUBLESHOOTING
Symptom
Possible causes
Solution
Machine does not start
when the switch is in”
I”position.
Power cord is not plugged in.
Plug in power cord.
Socket is defective
.
Check or replace plug, socket, fuses.
GFCI is triggered.
Press reset on GFCI plug.
Machine pressure is
not consistent.
Pump is faulty.
Contact service center .
Air in line.
Remove the nozzle, turn on the machine for a while and
install the nozzle back.
Water inlet adapter is clogged
or dirty.
Remove the adapter, rinse it with water and put is back.
The pressure of the
pump is not adequate
Water supply is Insufficient.
Open water source completely.
Water supply is restricted.
Check If the water hose kinks or leaks.
Diameter of garden hose is too
small.
Replace with right garden hose .
Leak or kick in hose .
Replace hose or untie kinks in hose.
No detergent
Wrong nozzle is attached
Attach the soap nozzle
Lance leaks
O-ring needs to be replaced(See
Fig. A1) .
Replace o-ring .If the problem is not solved ,contact service
center to buy a new lance.
Содержание WG605
