Worx WG349, Руководство пользователя

Страница: 15 / 22

Cordless Chainsaw EN
15
ATTACHING AND ADJUSTING THE AUXILIARY
HANDLE
Install the auxiliary handle onto the extension pole.
Tighten the auxiliary handle with the Auxiliary
Handle Locking Knob (19). (See Fig. H1)
To adjust the auxiliary handle, unscrew the Auxiliary
Handle Locking Knob (19) counter-clockwise to
unlock, as indicated. Hold the lever and rotate the
Auxiliary Handle (26) to the most comfortable and
balanced position (See Fig. H2).
Tighten the Locking Knob (19) clockwise to lock, as
indicated.
ADJUSTING THE SAW HEAD ANGLE
The saw head can be rotated for different cutting
angles for 0o, 15o, and 30o. (See Fig. I1)
1. Rotate the pole saw head to the desired cutting
angle while pressing the Saw Head Adjustment
Knobs located on both sides simultaneously. (See
Fig. I2)
2. Release the knobs when the pole saw head is set
to the desired angle.
NOTE: Failure to properly secure the pole saw
head may result in personal injury and/or property
damage.
WARNING! Always ensure the pole saw
head is securely locked! Do not attempt
to use the pole saw with the head in any other
position or unlocked!
ADJUSTING THE REAR HANDLE (See Fig. J)
Push the rotating lock button forward to unlock. Hold
the rear handle and rotate it to the most comfortable
and balanced position. Release the rotating lock
button to lock the rear handle.
WARNING: Always make sure that the
handle is locked in the desired position
before operation. Do not rotate the handle
when the saw is being operated.
LUBRICATION
IMPORTANT:
The pole saw is not filled with
oil. It is essential to fill with oil before use.
Never operate the pole saw without chain oil or at an
empty oil tank level, as this will result in extensive
damage to the product.
NOTE: Chain life and cutting capacity depend
on optimum lubrication. Therefore, the chain is
automatically oiled during operation.
FILLING OIL TANK (See Fig. K)
WARNING: Removing the battery pack
before filling the oil tank.
1. Set pole saw on any suitable surface with Oil Filler
Cap (6) facing upward.
2. Clean area around the Oil Filler Cap with cloth and
unscrew the cap by turning it counter clockwise.
3. Add bar and chain oil (not included) until tank is
full.
4. Avoid dirt or debris entering oil tank, refit Oil Filler
Cap (6) and tighten by turning clockwise until hand
tight.
IMPORTANT: To allow venting of the
oil tank, small breather channels are
provided between the Oil Filler Cap and the
strainer, to prevent leakage, and ensure
machine is left in a horizontal position (Oil
Filler Cap (6) uppermost) when not in use.
It is important to use only the recommended
standard bar and chain oil (Grade: ISO VG32)
to avoid damage to the pole saw. This can be
found at the location where you purchased this
saw or your local hardware store. Never use
recycled/old oil. Use of non approved oil will
void the warranty.
Do not swallow. If swallowed, call a physician
immediately. Keep out of reach of children.
Store away from heat or open flame.
Checking the Automatic Oiler
Proper functioning of the automatic oiler can be
checked by running the pole saw and pointing the
tip of the Guide Bar (7) towards a piece of cardboard
or paper on the ground. If an increasing oil pattern
develops on the cardboard, the automatic oiler is
operating fine. If there is no oil pattern, despite a full
oil reservoir, contact WORX customer service agent
or WORX approved service agent.
CAUTION: Do not touch the ground with
the chain. Ensure safety clearance of
13ft.
OPERATION
1. BEFORE USING YOUR CORDLESS TOOL
WARNING!
The charger and battery pack
are specially designed to work together so do
not attempt to use any other devices. Never insert
or allow metallic objects into your charger or battery
pack connections because of an electrical failure and
hazard will occur.
NOTE:
Your battery pack is UNCHARGED and you
must charge once before use.
The battery charger supplied is matched to the Li-ion
battery installed in the machine. Do not use another
battery charger.
2. CHARGING YOUR BATTERY PACK
The Li-ion battery is protected against deep
discharging. When the battery is empty, the machine
is switched off by means of a protective circuit.
In a warm environment or after heavy use, the
battery pack may become too hot to permit charging.
Allow time for the battery to cool down before
recharging.
3. TO REMOVE OR INSTALL BATTERY PACK
(See Fig. L1, L2)
Depress the Battery Pack Release Button to remove
the Battery Pack from your tool. After recharging,
insert the Battery Pack into the battery port. A simple
push and slight pressure will be sufficient until a click
is heard. Check to see if the battery is fully secured.