Worx WG166, Инструкция по эксплуатации

Страница: 11 / 32

11 10
2-in-1 Cordless Lawn trimmer / Lawn edge trimmer EN
11 10
3. To REMovE oR INSTALL BATTERy
PACK
Locate latches on side of battery pack and
depress both sides to release battery pack
from your grass trimmer. Remove battery
pack from your grass trimmer (See D). After
recharge insert the battery pack into grass
trimmer’s battery port. A simple push and
slight pressure will be sufficient.
4. SAFETy oN/oFF SwITCH
Your switch is locked off to prevent accidental
starting. Depress lock off button (B) then on/off
switch (A) and release lock off button (B). Your
switch is now on. To switch off just release the
on/off switch (See Fig E).
wARNING: The cutting head
continues to rotate after the trimmer
has been switched off, wait until it has
stopped then lay down the tool.
5. ADJUSTMENT oF THE TELESCoPIC
SHAFT (See Fig F)
Unscrew the lower locking knob (4) in the
direction indicated to unlock.
Adjust the length of the telescopic shaft to the
most comfortable length.
Tighten the lower locking knob.
6. MAIN HANDLE RoTATIoN (See Fig G)
Unscrew the upper locking knob (3) in the
direction indicated to unlock
Adjust the angle of the main handle to be
clockwise 90 degree max.
Turn the upper locking knob in the opposite
direction to lock.
7. ADJUSTMENT oF AUxILIARy HANDLE
Pull up the auxiliary handle locking lever (12).
Hold the lever and rotate the auxiliary handle
to the most comfortable and balanced position
(See Fig H)
Release the lever, your auxiliary handle has
been locked.
8. ADJUSTMENT oF THE TRIMMER
HEAD ANGLE To THE SHAFT
Use both of your hands, one grips the shaft,
another on the head, then apply adequate
force to adjust the trimmer head to the most
comfortable position. The ratchet mechanism
will make a heavy clicking sound which is
normal and not a defect (See Fig I).
opEraTioN
wARNING:
Always wear the eye
protection. Never lean over the trimmer
head. Rocks or debris can ricochet or be thrown
into eyes and face and cause blindness or other
serious injury. When operating unit, check for
the following:
Wear eye protection and heavy clothing. Hold
front handle with one hand and auxiliary handle
with the other hand. Keep unit below waist
level. Work only from your right to your left to
ensure debris is thrown away from you. Without
bending over, keep line near and parallel to the
ground (perpendicular when edging) and not
crowded into material being cut.
wARNING: Make sure that line is
fed out before operation. Make
sure motor is up to full speed before
trimming.
wARNING:
Use only 0.065” (1.65mm)
cutting line. diameter line. Other sizes of
line will not feed properly and will result in
improper cutting head function or can cause
serious injury. Do not use other material
such as wire, string, rope, etc. Wire can break
off during cutting and become a dangerous
missile that can cause serious injury.
Trimming
Hold the bottom of the trimmer head about
3.25”(8 cm) above the ground and at an angle.
Allow only the tip of line to make contact. Do
not force trimmer line into work area.
Edging(See Fig J)
Unscrew the upper locking knob (3) and rotate
the main and auxiliary handle to 90o with
cutting head (See Fig J).
Retighten the upper locking knob.
Adjust trimmer head angle to be the lowest
horizontal setting. Then position the wheel on
the ground for edge mode. The guard has two
white line guides to indicate the cutting line
position. Align these marks with the edge of
your lawn.
While edging allow the tip of the line to make
contact. Do not force the line. The rotation
wheel helps protect the unit and keeps the