Worx Nitro WG186E.1, Оригинальная инструкция, Страница: 20 / 300

Cordless Grass Line Trimmer &
Brushcutter, Attachment-Capable
20
EN
ECO Speed
For longer run time, press the ECO
button and switch trigger, then your
machine will operate at a low speed.
See Fig. G
Trimming See Fig. H
Bump feed See Fig. I
Assembling and removing the
trimmer head
Insert the hex key into the hole and
rotate the trimmer head until it stops
in a locked position. Then, rotate
counterclockwise to remove it, and
clockwise to assemble it.
See Fig. J
Winding the trimmer line
NOTE:
The spool must be wound
while inside the trimmer head. The
spool cannot be wound with line,
then installed into the trimmer head.
See Fig. K
Assembling the brush cutter blade
Remove the trimmer head and the
skirt before assembling the brush
cutter blade.
Insert the hex key into the hole.
Place the brush-cutter blade on top
of the spacer, place washer on top of
the brush-cutter blade, place blade
housing over washer. After that, use
the wrench to tighten the lock-nut.
See Fig. L1,
L2, L3
Cutting See Fig. M
ATTACHMENT-CAPABLE ACCESSORIES
The below attachment accessories are sold
separately to convert the grass trimmer into a tool
for various applications.
1. Pole hedge trimmer attachment (WA0220)
This attachment is intended for cutting and
trimming hedges and bushes in domestic use.
2. Pole saw attachment (WA0222)
This attachment is intended for sawing of trees,
tree trunks, branches, limbs, etc. Cuts can be
sawed with or across the grain. This product is
not suitable for sawing mineral materials.
3. Edger attachment (WA0223)
This attachment is intended for edging around
walkways, driveways, flower beds, etc.
BATTERY STATUS (See Fig. E5)
Before starting or after use, press the button beside
the power indicator light on the machine to check
the battery capacity. During operation, the battery
capacity will be indicated automatically by the battery
power indicator.
The indicator constantly senses and displays the
battery condition as follows.
For the machine with 2 battery packs with different
power, the power indicator light displays the battery
condition with the lower one of the two batteries.
Battery power
indicator status
Battery condition
Five green lights
( ) are
illuminated.
The two batteries are in a
highly charged condition.
Two, three or four
green lights are
illuminated.
The two batteries have a
remaining charge. The more
lights are illuminated, the
more battery capacity.
Only one green light
( ) is
illuminated.
At least one battery is
almost depleted and needs
to be charged.
No light is
illuminated.
At least one battery is not
fully installed or battery may
be defective.
Only one light is
flashing twice per
cycle.
At least one battery is
over discharged (please
refer to the battery charge
condition), please recharge
the two batteries at once
before use again or storage.
Only one light is
flashing three times
per cycle.
At least one battery is hot,
wait for them cool down
before start again.
Only one light is
flashing four times
per cycle.
The machine is over load.
Raise the cutting height or
push slowly.
OPERATION INSTRUCTIONS
WARNING! The charger and battery pack
are specially designed to work together so do
not attempt to use any other devices. Never insert or
allow metallic objects into your charger or battery
pack connections because of an electrical failure and
hazard will occur.
1. Bump-line feed system (See Fig. I)
The trimmer is equipped with a bump-line system.
Just bump the trimmer head while the machine is
running, new line will feed out.
2. Winding the trimmer line (See Fig. K)
Insert the replacement line through the eyelet and feed it
through the other side. Ensure both ends of the line are
even on each end of the trimmer head (max 3m) and cut
the line. Turn the dial clockwise to wind the line around the
spool until about 19cm remains on either side.