Cordless Limbing and Trimming Chain Saw en
17
16
17
16
H). The cutting direction is inward on the
lower cutting edge.
9. With the mounting plate (a) side of the
Guide Bar facing the Motor (8) and holding
the Saw Chain in place on the bar, feed bar
and chain into the jaw, angling over the
bar locating pins (d) and pulling the Saw
Chain over the drive Sprocket (17) (See
Fig. I). There will be little excess Saw Chain
length, therefore, the Saw Chain must
be properly fitted in the Guide Bar slot to
provide enough extra chain to be pulled
over the drive Sprocket.
10. Check if all parts are seated properly. (See
Fig J)
11. Refit and tighten the Chain Tensioning Bolt.
Note the cam (e) of the Chain Tensioning
Bolt will engage the projecting tab (f) of
the bar mounting plate and push the bar
outward to tension the chain, check for
correct tension (See Adjusting the chain
tension).
12. Close the Chain Access Cover and remove
the Lock Pin.
LUBRICATIOn
iMPoRTaNT: The JawSaw
®
is
shipped with an empty oil tank. it
is essential to fill with chain oil before
use. Bar and chain oil of any brand can
be used.
Never operate the JawSaw
®
without
chain oil or an empty tank as this will
result in poor cutting performance,
motor overload and possible burn-out.
FiLLiNg oiL TaNk:
1. Fill Oil Bottle (19) with chain and bar oil.
(See Fig. K)
2. Rest the JAWSAW
®
with the Oil Filler facing
upward.
3. Uncrew the oil filler cap (g) open.
4. Use bottle to fill oil reservoir. (See Fig. L)
5. Screw the oil filler cap.
iMPoRTaNT: use only the
recommended oil to avoid damage
to the JawSaw
®
. Never use recycled/
old oil. use of non approved oil will
invalidate the warranty.
CHECkiNg THE auToMaTiC oiLER
The JAWSAW
®
uses a much lower chain speed
than a conventional chainsaw so it needs
much less oil.
However it is very important that it always has
oil.
Check the Oil Level Window (14) and refill as
necessary.
During operation, periodically check the
Saw Chain (8) and Guide Bar (7). A slight oil
presence should be visible. If the chain and
bar appear completely dry, then remove the
bar and chain (see previous section) to ensure
the bar oil hole is not blocked.
If the oil hole is clear, there is oil in the tank
and still no oiling of the chain is visible –
contact WORX customer service.
waRNiNg: do not push the rear
handle repeatedly when the saw is
not cutting. The oil will be bumped out
when pushing the handle whether the
motor runs or not.
OPeRATIOn
1. BEFoRE uSiNg youR CoRdLESS
JawSaw
®
Your battery pack is UNCHARGED and you
must charge once before use
The battery charger supplied is matched to the
Li-ion battery installed in the machine. Do not
use another battery charger.
2. CHaRgiNg youR BaTTERy PaCk
The Li-ion battery is protected against deep
discharging. When the battery is empty,
the machine is switched off by means of a
protective circuit.
In a warm environment or after heavy use, the
battery pack may become too hot to permit
charging. Allow time for the battery to cool
down before recharging.
3. To REMovE oR iNSTaLL BaTTERy
PaCk (See Fig.M)
Depress the battery release button to release
battery pack from your JAWSAW
®
. After
recharging, insert the battery pack into
the battery port. A simple push and slight
pressure will be sufficient.
Содержание JawSaw WG320
