Worx Nitro WG761E, Инструкция по эксплуатации

Страница: 12 / 24

12
Cordless Lawn mower EN
OPERATION
Starting and Stopping
NOTE: Place the Mulching-Bag Switch
Lever in the bag position after each
use. (See Fig. C1)
See Fig. J1, J2
Operating the self-propel system See Fig. K
Adjusting the cutting height
WARNING! Stop, release
Operating Bail and wait until the
motor stops before adjusting height.
The blades continue to rotate after
the machine is switched off, a rotating
blade can cause injury. Do not touch
rotating blades.
See Fig. L
Opening the LED headlight See Fig. M
Removing/emptying grass collection
bag
WARNING! Always check the
safety flap close the discharge
outlet before using. Never lift the
safety flap when the lawn mower
is being used without fitted grass
collection bag.
See Fig. N1,
N2
Storage See Fig. O1,
O2
BATTERY STATUS (See Fig. I)
Light ON/ Flash Status
One Red on
Two LED-lights
off
Defective Battery
One Red flash
Two LED-lights
off
----------
Battery Temperature
Protection
The temperature of battery
pack is less than 0
0
C or
more than 45
0
C
Three Green on
Fully Charged
Three Green
flash
---------- Charging
MULCHING MOWING TIPS
While mulching, your new mower is designed to cut the
grass clippings into small pieces and distribute them
back into the lawn. Under normal conditions, the mulched
grass will biodegrade quickly and deliver nutrients to the
lawn. Please review the following recommendations for
optimum mulching performance.
1) Avoid mowing when the grass is wet from rain or dew.
Wet grass may form clumps which interfere with the
mulching action and reduce the runtime. The best
time to mow the grass is in the late afternoon when the
grass is dry and the newly cut area will not be exposed
to direct sunlight.
2) For the best mulching performance, set the cutting
height to remove about one third of the grass blade
length, ideally no more than 40mm at one time. If the
lawn is overgrown, it may be necessary to increase the
cutting height to reduce the pushing effort and prevent
overloading the motor. For extremely heavy mulching,
it is advisable to first cut at a high cut height setting,
and then re-cut to the final cut height. Otherwise, make
narrower cuts and mow slowly.
3) For the best performance, keep the mower housing
free of built-up grass. From time to time turn off
mower and wait for the blades to come to a complete
stop. Then Remove the safety key and turn mower
on its side. Using an object such as a stick, wipe out
any accumulation of grass around the blade area. Be
careful of the sharp edges of the blade. Ensure to clean
the blade area often when cutting wet or new grass and
every time after the machine is used.
4) Certain types of grass or grass conditions may require
that an area be mulched a second time to fully disperse
the grass throughout the lawn. If cutting a second time,
it is advisable to cut perpendicular (across) the first cut
pattern. DO NOT CHANGE CUT PATTERN IN ANY WAY
THAT WOULD CAUSE MOWING DOWN A HILL.
5) Change your cutting pattern from week to week. This
will help prevent matting and graining of the lawn.
6) Do not mow on a slope that has an angle of greater
than 15
0
.
CUTTING AREA
The cutting area can be affected by several factors, such
as cutting height, lawn humidity, grass length and density.
Besides, starting and stopping the mower too many times
during operation will reduce the cutting area.
The table below gives the relationship between cutting
conditions and cutting area.
Cutting Height
Recommend lot size
(maximum)
Cutting off 8cm to 6cm
With 4*20V / 4.0Ah batteries
up to 1000m
2
*
* Use with 4 fully charged battery packs. If batteries of
differing amp hours are used together, the product will
operate to the lowest common denominator.
TIPS:
1) It is recommended to mow your lawn more frequently,
walk at normal pace, and not to start/stop the mower
too often during operation.