manualshive.com logo in svg

Worksaver GBH-2072R, Руководство владельца/оператора

Поделиться
Скачать
Worksaver GBH-2072R Скачать руководство пользователя страница 6

5

SAFETY INSTRUCTIONS 

(continued)

OPERATIONAL SAFETY

Be sure power unit is in good condition. Read all the safety precautions and make sure all operators are famil-
iar with the safety rules of operation.

Never leave the tractor and implement unattended while the implement is in the lifted position. Accidental oper-
ation of lifting lever or a hydraulic failure may cause sudden drop of unit with injury or death by crushing.

Keep all helpers and bystanders twenty-five feet (25’) from an operating power unit and attached equipment.
Only properly trained people should operate this machine. It is recommended the tractor be equipped with a
Rollover Protection System (ROPS) and a seat belt that is used. Always stop the tractor, skid steer, or forklift,
set brake, shut off the engine, remove the ignition key, and lower loader and attachment to the ground before
dismounting. Never leave equipment unattended with the engine running.

Please remember it is important that you read and heed the safety signs on the front loader attachment and
loader, and the safety rules set forth. Clean or replace all safety signs if they cannot be clearly read and under-
stood. They are there for your safety as well as the safety of others. The safe use of this machine is strictly
up to you, the operator.

The use of any loader attachment is NOT recommended on tractor with a tricycle wheel arrangement. Tricycle
type tractors are unstable for front loader use.

A heavy load can cause instability in driving a power unit. Make sure the front or rear of the power unit is
properly counter-balanced with weights. Always drive slowly – especially around turns. An unstable power unit
could steer badly and possibly tip over, causing injury or death.

When the use of hand tools is required to perform any part of assembly, installation, adjustment, maintaining,
repairing, removal, or moving the implement, be sure the tools used are designed and recommended by the
tool manufacturer for that specific task.

Never allow children to play on or around tractor or implement. Children can slip or fall off the equipment and
be injured or killed. Inadvertent contact with controls can cause the implement to shift or fall crushing them-
selves or others.

Always use two people to handle heavy, unwieldy components during assembly, installation, removal, or
moving the loader attachment.

Never place any part of your body where it would be in danger if movement should occur during assembly,
installation, operation, maintaining, repairing, removal, or moving the implement.

Start tractor only when properly seated in the tractor seat. Starting a tractor in gear can result in injury or death.
Do not mount or dismount the tractor while the tractor is moving. Mount or dismount the tractor only when the
tractor and all moving parts are completely stopped.

Operate the tractor and/or implement controls only while properly seated in the tractor seat with the seat belt
securely fastened around you. Inadvertent movement of the tractor or implement may cause serious injury or
death.

Содержание GBH-2072R

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды