Workrite ES2E54-72 Скачать руководство пользователя страница 10

Страница: 10 / 10

10 of 10

Workrite Ergonomics | 800.959.9675 www.workriteergo.com

#1500244 Rev D

Put Workcenter Upright and Connect Power Cord to the Power Supply

Turn the workcenter over into an upright position.
Plug the Power Cord (N) into the power outlet.

Initialize Legs

After all Legs and the Switch are connected, and the power cord has been plugged in, hold the

down arrow on

the Switch until the Legs make a short motion down and then back up. This initializes and synchronizes the

workcenter Legs.

Adjust Feet Glides

If necessary, adjust Leveling Glides on workcenter feet to level the worksurface. Unscrew to increase height,

screw in to decrease height.

You must complete this

initialization step or your

workcenter will NOT

function properly.

Cleaning Instructions

To clean the Essentia legs, apply cleaner to a soft cloth.
Suggested cleaners: Windex or Formula 409.

Do not use solvents and do not saturate or spray cleaners directly onto workcenter base.

Hold down the down arrow

until workcenter moves slightly

upwards!

✓

Parts & Accessories

Visit

http://workriteergo.com/documentation/other/workrite_ergonomics_pricing_specification_guide.pdf

for

replacement parts.

✓

Содержание ES2E54-72











Результаты поиска

Содержание ES2E54-72

Отзывы:

Похожие инструкции для ES2E54-72

Бренды по названию

Популярные бренды

Workrite ES2E54-72, Сборка и инструкция по установке

Результаты поиска

Содержание ES2E54-72

Отзывы:

Похожие инструкции для ES2E54-72

Бренды по названию

Популярные бренды