Workrite Ergonomics Conform CONF-1SDS-WOPB-S Скачать руководство пользователя страница 6

6 of 6  

Workrite Ergonomics  |  800.959.9675  www.workriteergo.com

Cable Management

Remove the arm covers by sliding them up, then off. 

Secure cables with Hook & Loop (G) strips. Slide covers on, then down to secure.

Route through Cable Management clips on pole.
Note: Leave sufficient slack in the cables to allow free movement of arm.  

Parts & Support

14" Pole Base with C-Clamp & Grommet .............................

CONF-PB-14CCG-S

28" Pole Base with Heavy Duty C-Clamp & Grommet  .........

CONF-PB-28HDCCG-S

Tool Bar & Slatwall Base .......................................................

CONF-BSE-TSB-S

Wall Plate Base ......................................................................

CONF-BSE-WP-S

Static Extension Arm .............................................................

CONF-ACC-1EXT-S

Single Pole Mount Adaptor ...................................................

CONF-ADPT-SPM-S

Dual Pole Mount Adaptor ......................................................

CONF-ADPT-DPM-S

Quick Release Adaptor ..........................................................

MON-ADPTVQR-W-B

Technical Support: Please call Workrite Technical Support while at the Workrite product. (800) 959-9675 option 2.

1500247 Rev D

6

b

b

b

a

Hook & Loop

Strips

Hook & Loop

Strips

On

Off

a

a

c

c

Содержание Conform CONF-1SDS-WOPB-S







Отзывы: