manualshive.com logo in svg

Workrite Ergonomics Conform CONF-1SDS-WOPB-S, Инструкции по сборке/установке

Поделиться
Скачать
Workrite Ergonomics Conform CONF-1SDS-WOPB-S Скачать руководство пользователя страница 1

1 of 6  

Workrite Ergonomics  |  800.959.9675  www.workriteergo.com

A

  Conform Static Arm 

Qty: 1

B

  Single Pole Mount 

Adaptor Assembly 

Qty: 1

Parts Included

Assembly & Installation Instructions:

Conform Static Arm CONF-1SDS-WOPB-S

Required Parts Sold Separately

Tools Required

Selected base option with mounting hardware.

Do not use on hollow core tables. 

Do not rotate or suspend arm beyond table surface. 

Do not exceed 16 lb. per Arm.

#2 Phillips head screwdriver 

2.5 mm Allen wrench (included with base) 

4 mm Allen wrench (included with base) 

5 mm Allen wrench (included with base)

E

  Wedge Washer 

Qty: 1

F

  Pivot Cover Cap 

Qty: 1

G

  Hook & Loop Strips    

Qty: 4

C

  M4 × 10 mm VESA mount screw 

Qty: 4

D

  M4 × 6 mm VESA mount screw 

Qty: 4

Attach the Single Pole Mount Adaptor to Selected Pole Option

Place the selected Single Pole Mount Adaptor 

Assembly (B) on the selected pole option, at 

your desired monitor height.

Tighten the clamp screw on the Single Pole 

Mount  Adaptor Assembly with the 5 mm 

Allen wrench, included with base, to secure 

Adaptor to Pole.

1

a

a

b

b

B

14" Pole shown

Clamp screw

Содержание Conform CONF-1SDS-WOPB-S







Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды