Worcraft CEP-S20LiB, Инструкция по эксплуатации

Страница: 46 / 59

overload.
●
The battery can be damaged by pointed objects such as
nails or screwdrivers or by force applied externally. An
internal short circuit can occur and the battery can burn,
smoke, explode or overheat.
●
Do not short-circuit the battery. There is danger of
explosion.
●
Protect the battery against moisture and water.
●
Store the battery only within a temperature range between
–
20 °C and 50 °C. As an example, do not leave the battery in
the car in summer.
●
Occasionally clean the venting slots of the battery using a
soft, clean and dry brush.
Safety Warnings for Battery Chargers
●
Never allow children, persons with physical, sensory or
mental limitations or a lack of experience and/or knowledge
and/or people unfamiliar with these instructions to use the
battery charger. Local regulations may restrict the age of the
operator.
● Supervise children at all times. This will ensure that
children do not play with the battery charger.
●
Keep the battery charger away from rain or moisture.
Penetration of water in the battery charger increases the risk
of an electric shock.
●
Keep the charger clean. Contamination can lead to danger
of an electric shock.
●
Before each use check the battery charger. If damage is
detected, do not use the battery charger. Never open the
battery charger yourself. All repairs must be performed by
Service Centre.
Damaged battery chargers and USB cables increase the
risk of an electric shock.
● Do not operate the battery charger on flammable
surfaces (e. g., paper, textiles, etc.) or surroundings. The
heating of the battery charger during the charging process can
pose a fire hazard.
●
Damage to the machine may cause vapours to be
emitted. Ventilate the area and seek medical attention in
case of discomfort.
The vapours can irritate the respiratory
system.
Appliance-specific safety Instructions for planers
●
Wait until the blade shaft has completely stopped
moving before you put the device down. An exposed
blade shaft may catch on the surface and lead to loss of
control or serious injury.
●
Do not place your fingers in the planer debris removal
port. Danger of injury from rotating parts.
●
Always switch on the device before placing it against
the workpiece. Otherwise the device could kick back if the
planer blade gets snagged in the workpiece.
●
When working always keep the sole flat against the
workpiece. Otherwise you could be injured if the plane tilts.
●
Never plane over metal objects. Otherwise the planer
blade / blade shaft could be damaged.
●
Secure the workpiece. Use clamps or a vice to grip the
workpiece firmly. This is much safer than holding it with your
hand.
●
Do not plane materials containing asbestos. Asbestos
is a known carcinogen.
●
The dust generated while planing could be hazardous
to health, inflammable or explosive. Wear a dust mask
and use a suitable dust / debris vacuum extraction device.
Some dusts are known carcinogens.
●
When planing wood for long periods and in particular
when working on materials that give rise to dusts that
are hazardous to health, the planer must be connected
to a suitable external dust extraction device.
●
Never support yourself by placing your hands near or
in front of the device or on the workpiece surface. If you
slip you could be injured.
● When taking a break from your work, before carrying
out any tasks on the device itself (e.g. changing the
plane blade) or when you are not using the device,
always
remove the battery pack.
● Use sharp planer blades only.
● Do not soak the materials or the surface you are about
to work on with liquids containing solvents.
● Avoid contact with rotating parts.
● Never use the device for a purpose for which it was
not intended or with non-original parts / accessories.
●
Hold the device securely when working. Ensure that
you are standing in a stable, well-balanced position.
●
Always keep the device clean, dry and free from oil or
grease.
SET UP AND OPERARION
WARNING!
Do not insert battery before the tool is
completely assembled.
ASSEMBLY
Prior to using the Tile cutting saw, the rubber feet, diamond
blade, bladeguard and parallel fence will need to be installed.
Fitting the parallel guide fence (fig.3)
1. Put the L-bracket onto the parallel guide fence, and align
the slot with the holes.
2. Put the bolt through the aligned holes.
3. Screw the screw nut and fasten it.
4. Put the pre-assembled parallel guide fence onto the
palner side, and then fasten securely with screw knob.
Fitting the rabbeting depth stop (fig. 4)
1. Put the rabbeting stop onto the planer housing right side,
and align the holes.
2. Secure it on the body with the screw knob.
Mounting the battery pack (fig. 5)
WARNING! Before mounting battery pack, be sure the switch
is on
“OFF” position.
Slide the battery into into the slot of tool rear body. After hear a
click sound, the battery pack was securely assembled
already.
Setting up the cutting depth (fig.6)
This planer can cutting wood with maximum 2mm,you can
roughly adjusting it by turn the big round knob clockwise or
anti-clockwise to get the desire cutting depth.
Turn clockwise to decrease cutting depth. And turn anti-
claockwise to increase cutting depth.
Setting dust exhaust direction (fig.7)
This tool designed left two sides dust exhaust port for
conveniently operation by right-hand person and left-hand
person.
Turn the lever left to make the dust exhaust from right side.
Turn the lever right to let the dust exhaust from left side.
Setting parallel cutting width (fig.8)
According your demand, you can adjust the parallel cutting
width as you wish.
1. Loosen the screw nut firstly.
2. Move the parallel guide fence inside or outside direction
to get the desire width.
3. Lock the screw knob again to secure it in position.