mounted in such a way that their grinding surface does not
protrude over the level of the edge of the protective cover.
An
incorrectly mounted grinding wheel which protrudes beyond the
level of the edge of the protective cover cannot be adequately
shielded.
c) The protective hood must be securely attached to the
electric tool and adjusted so that the greatest level of safety
is reached
, i.e., the smallest possible amount of the grinder is
exposed to the operator. The protective hood should protect the
operator from broken bits and accidental contact with the grinder.
d) Grinders may only be used for the recommended
attachment options.
For example: Never grind with the side
surface of a cutting disc. Cutting discs are for cutting material
using the edge of the disc. Pushing sideways on these grinders
can break them.
e) Always use undamaged clamping flanges of the correct
size and shape for the grinding disc you selected.
Suitable
flanges support the grinding disc and thus reduce the danger of
the grinding disc breaking. Flanges for cutting discs can be
distinguished from flanges for other grinding discs.
f) Do not use worn grinding discs for larger electric tools.
Grinding discs for larger electric tools are not set up for the higher
rotation speeds of smaller electric tools and can break.
Other special safety instructions for cutting grinding
a) Avoid blocking the cutting disc or pressing down too hard.
Do not make any excessively deep cuts. Overloading the cutting
disc increases wear and its tendency to tilt or block and, with that,
to kickback or break the grinder.
b) Avoid the area in front of and behind the rotating cutting
disc.
When you move the cutting disc by itself in the workpiece, in
the event that the electric tool kicks back with the rotating disc, it
can spin directly towards you.
c) If the cutting disc jams, or you interrupt your work, switch
the device off and hold it until the disc has come to a full
stop
. Never try to pull the cutting disc out of the cut while it is still
running, because it can kick back. Identify and correct the cause
of the jamming.
d) Do not switch the electric tool on again as long as it
is in the workpiece.
Allow the cutting disc to first reach its
full rotational speed before you carefully resume with the
cutting. Otherwise, the disc may catch, spring away from
the workpiece or cause a kickback.
e) Support plates or workpieces to reduce the risk of
kickback from a jammed cutting disc.
Large workpieces
may bend under their own weight. The workpiece must be
supported on both sides of the disc, near the cutting disc
as well as also at the edge.
f) Be particularly careful for pocketcuts in existing
walls or other areas where you cannot see what is
there.
The cutting disc may cause a kickback when it cuts
into gas or water lines, electrical lines or other hidden
objects.
Additional safety instructions for sanding
Special safety instructions for sanding:
•
Do not use overly large sandpaper sheets; follow the
manufactu
rer‘s information for sandpaper sizes.
Sandpaper sheets which extend beyond the sanding plate
can cause injuries and can block, tear the sandpaper, or
cause kickback.
Additional safety instructions for working with wire
brushes
Special safety instructions for working with wire brushes:
•
Be aware that the wire brushes also lose wire pieces
during typical use. Do not overload the wires by
pressing down too hard.
Flying wire pieces can very
easily penetrate thin clothing and/or your skin.
•
If a protective hood is recommended, do not allow
the wire brushes and the protective hood to touch
each other.
The diameter of plate and cup brushes can
enlarge if too much pressure and centrifugal force is
exerted.
ASSEMBLY
／
OPERATION
MAINTENANCE
Make sure that the machine is not live when carrying out maintenance work on the motor. Regularly clean the machine
housing with a soft cloth, preferably after each use. Keep the ventilation slots free from dust and dirt. If the dirt does not come
off use a soft cloth moistened with soapy water. Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents
may damage the plastic parts.
The machine requires no additional lubrication. If a fault occur, e.g. after wear of a part, please contact your local dealer
’s service.
ENVIRONMENT PROTECTION
In order to prevent the machine from damage during transport, it is delivered in a sturdy packaging. Most of the packaging
materials can be recycled. Take these materials to the appropriate recycling locations. Take your unwanted machines to your
local dealer. Here they will be disposed of in an environmentally safe way.
Li-ion batteries can be recycled. Deliver them to a disposal site for chemical waste so that they can be recycled or
disposed of in an environmentally friendly manner.
Discarded electric appliances are recyclable and should not be discarded in the domestic waste! Please actively
support us in conserving resources and protecting the environment by returning this appliance to the collection
centres (if available).
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents:
EN60745-1:2009+A11:2010; EN60745-2-3:2011+A2:2013+A11,A12:2014+A13:2015; EN55014-1:2006/+A1
：
2009/+A2:2011;
EN55014-2:2015; in accordance with the regulations 200
6/42/ЕС, 2014/30/ЕU.
NOISE/VIBRATION Measured in accordance with EN60745 the sound pressure level of this tool is <88dB(A) and the sound
power level is <99dB(A) (standard deviation: 3 dB), and the vibration is <4,9 m/s
2
.
