Worcraft PROFESSIONAL S010-3.6Li, Инструкция по эксплуатации

Страница: 43 / 54

Water entering a power tool will increase the risk of electric shock.
●
Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat, oil,
sharp edges and moving parts. Damaged or entangled cords
increase the risk of electric shock.
●
When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
●
If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use of an
RCD reduces the risk of electric shock.
Personal safety
●
Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while you
are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in
serious personal injury.
●
Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
●
Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing
power tools that have the switch on invites accidents.
●
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
●
Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected
situations.
●
Dress properly. Do not wear loose clothing or jewellery. Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
●
If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly
used. Use of dust collection can reduce dust-related hazards.
Power tool use and care
●
Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer
at the rate for which it was designed.
●
Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
●
Disconnect the plug from the power source and/or the
battery pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
●
Store idle power tools out of the reach of children and do not
allow persons unfamiliar with the power tool or these instructions
to operate the power tool. Power tools are dangerous in the hands
of untrained users.
●
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any other
condition that may affect the power tool
’s operation. If
damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power
tools.
●
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
●
Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
Service
●
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Safety notices specific to drills
Hold the device by the insulated handle
surfaces when you are undertaking work where
there is the danger of the screw striking hidden
electricity cables or
the device’s mains lead.
Contact
of the screw with a live wire could cause metal parts of
the device to become live and lead to electric shock.
●
Children or persons who lack the knowledge or
experience to use the device or whose physical, sensory
or intellectual capacities are limited must never be
allowed to use the device without supervision or
instruction by a person responsible for their safety.
Children must never be
allowed to play with the device.
●
Securely support the workpiece. A workpiece held in a
clamp or vice is kept more securely in place than one
held by your hand.
POISONOUS DUSTS!
Harmful / noxious dusts generated from your work
represent a risk to the health of the person operating the
device and to anyone near the work area. Wear safety
glasses and a dust mask!
●
Do not drill any material containing asbestos. Asbestos
is a known carcinogen.
●
Hold the electrical power tool firmly. High reaction
torques may occur momentarily during tightening or
loosening of screws.
●
If the inserted tool jams, switch off the electrical power
tool immediately. Be prepared for high reaction torques
as they may cause kickback. The inserted tool may jam if
the electrical power tool is overloaded or is held at an
angle to the workpiece.
●
Before you carry out any tasks on the device, transport
or store it, make sure that the direction of rotation switch
is in the middle position (lock). To prevent the device
from starting up unintentionally
OPERATION
Assembly screwdriver bits (Fig. 3)
Align the bits to the spindle holder and insert it. The bits will
automatically slipped into its position, because this bits holder
equipped a magnetic block in it.
After that, make a pull test to make a test to check if it is already
secured in it.
Swithing on/ off (Fig. 4)
Screw into wood, press the knob(4) to the left, then press the
switch trigger(1),the tool will run clockwise and the LED working
light (3) also lit at the same time.
To remove the screw from the wood, press the knob(4) to
the right, then press the switch trigger(1),the tool will run
anti-clockwise and the LED working light (3) also lit at the
same time.
To switch off the tool, just releasr the switch knob.
Adjust the body direction (Fig.5)
For comfortable operation,the tool designed can be
operated not only as a gun type, but also as straight