Worcester GR2300iW C Скачать руководство пользователя

Страница: 67 / 100

Replacement parts

Greenstar 2000 – 6 721 820 552 (2021/02)

Replacement parts

WARNING

Mains supplies - Isolate the appliance

▶ Turn off the gas supply and isolate the mains electrical supply before

starting any work and observe all relevant safety precautions.

▶ Drain the appliance/system where necessary and protect any

electrical equipment from water ingress during component
replacement.

WARNING

Component replacement:

▶ After replacement of a gas carrying component, where a gasket or

seal has been disturbed or replaced, check for gas tightness using a
gas sniffer/leak detection fluid.

▶ On re-assembly check all affected seals for cracks, hardness and

deterioration.



If damaged or in any doubt the seal must be replaced.

▶ Also after re-assembly, carry out the following checks:



Fan pressure.



Flue gas analysis.

Only use Worcester, Bosch Group original spare parts with this
appliance. Non Worcester, Bosch Group original spare parts will
invalidate the guarantee (if applicable) and any warranty.

▶ A comprehensive list of appliance spares can be found on the website

www.worcester-bosch.co.uk/spares

10.1

Component access

Removing the front casing

The front casing is secured with two screws which are critical to maintain
the case seal and to prevent unauthorised removal (electrical safety).

▶ Always secure the casing with these screws.

▶ Loosen the two screws [1] and pull the bottom of the casing forward.
▶ Lift off the casing.

Fig. 89 Removing the front casing

10.2

Draining the appliance

CAUTION

Risk of scalding!

▶ Take care when draining down, hot residual water can represent a

potential scalding risk

NOTICE

Risk of water damage to appliance or property!

Damage from disconnecting water pathways which may have retained
some water.

▶ Take care after draining the appliance to protect equipment/property

from residual water content within components.

Many of the tasks in this section require that the appliance be isolated
and drained. This will be indicated in the manual if required.

Refer to figure 90.
▶ Open the drain plug using a 8mm hex key; use a suitable container to

collect any water.

Fig. 90 Drain point

0010029675-001

0010029499-001

8mm

Содержание GR2300iW C





































































































Результаты поиска

Содержание GR2300iW C

Отзывы:

Похожие инструкции для GR2300iW C

Бренды по названию

Популярные бренды

Worcester GR2300iW C, Инструкция по установке и обслуживанию

Результаты поиска

Содержание GR2300iW C

Отзывы:

Похожие инструкции для GR2300iW C

Бренды по названию

Популярные бренды