manualshive.com logo in svg

Woods TURFKEEPER PRO TKP60.40, Руководство оператора

Поделиться
Скачать
Woods TURFKEEPER PRO TKP60.40 Скачать руководство пользователя страница 4

4 

Introduction

MAN11313 (3/3/2021)

SPECIFICATIONS

GENERAL INFORMATION

The purpose of this manual is to assist you in operating
and maintaining your mower. Read it carefully. It fur-
nishes information and instructions that will help you
achieve years of dependable performance. These
instructions have been compiled from extensive field
experience and engineering data. Some information
may be general in nature, due to unknown and varying
operating conditions. However, through experience
and these instructions, you should be able to develop
procedures suitable to your particular situation.



Some illustrations in this manual show the

mower with safety shields removed to provide a
better view. The mower should never be operated
with any safety shielding removed.

The illustrations and data used in this manual were cur-
rent at the time of printing. However, due to possible
inline production changes, your machine may vary
slightly in detail. We reserve the right to redesign and
change the machines as may be necessary without
notification.

Throughout this manual, references are made to right
and left directions. These are determined by standing
behind the tractor facing the direction of forward travel.

TKP60.40

TKP72.40

TKP84.40

3-Point Hitch

Cat.1 & Lim Cat.1

Cat. 1

Cat. 1

Quick Hitch Compatible

Factory Ready

Factory Ready

Factory Ready

Cutting Width

60"

72"

84"

Cutting Height Range

1-1/2” - 5"

1-1/2” - 5"

1-1/2” - 5"

Operating Weight with Chain Shielding

636 lbs

709 lbs

817 lbs

Deck Plate Thickness

7 GA

7 GA

7 GA

Blade Speed (feet per minute)

18,000

18,100

18,100

Blade Spindles

Ductile Iron

Ductile Iron

Ductile Iron

Number of Blades

3

3

3

Blade Overlap

1-1/2"

1-1/2"

1-1/2"

Blade Options

Standard: High Lift

Option: Low Lift

Standard: High Lift

Option: Low Lift

Standard: High Lift

Option: Low Lift

Universal Drive Series

ASAE Cat. 3

ASAE Cat. 3

ASAE Cat. 3

Caster Wheels

4.0 x 10.0

Solid Rubber

4.0 x 10.0

Solid Rubber

4.0 x 10.0

Solid Rubber

Tractor PTO Speed RPM

540

540

540

Recommended Maximum 
Tractor PTO Horsepower

50 max.

50 max.

50 max.

Chain Shielding

Optional

Optional

Optional

Front Roller

Optional

Optional

Optional

WARNING

Содержание TURFKEEPER PRO TKP60.40



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды