manualshive.com logo in svg

Woods 1187272, Руководство оператора, Страница: 14 / 36

Поделиться
Скачать
Woods 1187272 Скачать руководство пользователя страница 14

14 

Operation

MAN0731 (9/19/2008)

Set brake, shut off engine, remove key, remove seat
belt and release operator restraint before leaving the
skid steer operator's seat.

Disconnect hydraulic hoses from quick couplers. Install
dust plugs and couple hoses together for storage.

Move skid steer coupler handles to the unlocked posi-
tion, Figure 8. Lock pins must be disengaged from
attachment retaining slots.

 Figure 8

. Skid Steer Coupler Handles - Unlocked

Move to the skid steer operator seat, fasten seat belt,
disengage operator restraint, and start engine.

Release brake and roll skid steer coupler until it is dis-
engaged from the attachment. The attachment should
be placed in storage position.

STORAGE

Keep brush away from intense heat or flame.

Brush material can ignite and burn.

Keep children and bystanders away from stor-

age area.

NOTICE

■  

Do not store polypropylene brushes in direct

sunlight. The material can deteriorate and crumble
before the bristles are worn out.

NOTICE

■  

Do not store the broom with weight on the

brushes. Weight will deform them, destroying the
sweeping effectiveness. To avoid this problem, use
optional storage stands.

Inspect the angle broom thoroughly and prepare for
storage. Repair or replace any damaged components.

Remove the angle broom as described in Removing
Angle Broom from Skid Steer" above.

PRE-OPERATION CHECK LIST
(OWNER'S RESPONSIBILITY)

___ Review and follow all safety rules and safety

decal instructions on page 5 through page 9.

___ Check that all safety decals are installed and in

good condition. Replace if damaged.

___ Check that all shields and guards are properly

installed and in good condition. Replace if dam-
aged.

___ Check that all hardware and cotter pins are prop-

erly installed and secured.

___ Check that equipment is properly and securely

attached to skid steer.

___ Do not allow riders.

___ Check and keep all bystanders away from equip-

ment working area.

___ Check all lubrication points and grease as

instructed in lubrication, page 16.

___ Check that all hydraulic hoses and fittings are in

good condition and not leaking before starting
skid steer. Check that hoses are not twisted, bent
sharply, kinked, frayed or pulled tight. Replace
any damaged hoses immediately.

___ Make sure skid steer ROPS and seat belt are in

good condition. Keep seat belt securely fastened
during operation.

CAUTION

Содержание 1187272





































Отзывы:

Нет отзывов