Diagram1.3
Diagram1.3
Start with the assembly of horizontal beams
Z6, W8, W13 and W19
(W = horizontal, S = vertical). The
labels as shown on , can be found on the end of each beam. Position the beams on the floor so
that you can still walk around the bed while it is in the building phase.
Attention! All horizontal beams (Z6, W3, W5, W8, W10, W12) should be set up so that the side with
the most circular indentations (= ) face the inner side, while the sides with only two
indentations face underneath. The surface of beams W13, W16, W17 and W23 with round
indentations should face the inner side.
During the beam assembly install the
falthead bolts
from
outside to inside
. From the inside screw a
size 6 flange nut using a screwdriver with size 10 attachment. But do not over tighten bolts.
Diagram1.1
Diagram1.1
Diagram1.2
Diagram1.2
Diagram1.2
Diagram1.2
page 2
The beams W3 and W10
, has a notch to support the mattress slats and these
notch should face upward. For the beams
W13 - W23
there will be an additional
bolts for the end of vertical beams, which are fixed from top to bottom
at the end of the beam with M6 flange nut. The horizontal beams on the upper
bunk are built from top to bottom so that it makes it easier to screw nuts with
screwdriver. Then tightly screw the bolts at the bottom so that it makes it easier
to construct the rest of the bed.
Ladder assembly:
in one end of five rung holes of beam Z2 add drops of wood
glue (included in delivery). Tap in the steps using a hammer and wooden board
( ). Do not put glue on the other side so that another step can be added
later to raise the height to 150 cm!
Diagram1.3
Diagram1.3
Diagram1.1
Diagram1.1
3 drops of glue
on the end of each
steps.
Wooden board
to fix the steps
in the rung holes
Z2
Z1
Set up the corner beams S1, S5, S6 and S8.
Make sure that the beams sides with 7 round indentations
face the middle beam.
Then assemble W5, W17, W12 and W23. The beams W17 and W23 can be interchanged depending on whether you want to
W10
W10
W3
W3
Holzdübel 8 x 36 mm
Spax-Schraube 35 mm
Spax-Schraube 35 mm
Diagram1.4
Diagram1.4
Diagram1.5
Diagram1.5
The slatted frame:
as shown in 15 wooden peg
should be placed between each slats. The peg is attached to
one side of every slat except for the 16th slat. Slats are placed
on the notch of beams W3 and W10 and fixed with wooden
screws.
The slatted frame should only be used with a
mattress on top for safety since there are space between
the slats.
Other option: If you would like a bunk bed without a
mattress, an extra slat can be added (“Playing platform Set”,
Order No. 650). The wooden pegs should be taken out and
collected for later use. ( ).
Safety rails: assemble
Z23 - Z26 with 35-mm screws in the
centre between the mattress and middle guard rails (
W5,
W23, W12, W17
). The front- (Z23) and back safety rails (Z26
and Z26) should be attached from inside and side safety rails
Z24 and Z25 attached from outisde.
Diagram1.1
Diagram1.1
Diagram1.4
Diagram1.4
Diagram1.5
Diagram1.5
Glue the rungs only on one side of the ladder (in
case the bunk shall be highered and rungs shall
be added to the ladder).
16mm 35mm
screws
110 mm
flathead bolt
flange nut
M6
WOODLAND reserves the right for printing errors © Copyrights by WOODLAND 1998
R
