Woodland Mills WG24 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 32

background image

WG24 Operator’s Manual

PERSONAL SAFETY

•

Stay alert

, watch what you are doing and use common sense when operating machinery. Do

not use a machine when you are tired or under the influence of drugs, alcohol, or medication.
A moment of inattention while operating machinery may result in serious personal injury.

•

Dress properly.

Do not wear loose clothing, dangling objects, or jewelry. Keep your hair,

clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be
caught in moving parts. Air vents often cover moving parts and should be avoided.

•

Use safety apparel and equipment.

Use safety goggles or safety glasses with side shields

which  comply  with  current  national  standards,  or  when  needed,  a  face  shield.    Use  a  dust
mask in dusty work conditions.   This applies to all persons in the work area.   Also use non-
skid  safety  shoes,  hardhat,  gloves,  dust  collection  systems,  and  hearing  protection  when
appropriate.

•

Do not overreach.

Keep proper footing and balance at all times.

•

Remove adjusting keys or wrenches

before connecting to the power supply or turning on

the machine. A wrench or key that is left attached to a rotating part of the machine may result
in personal injury.

•

Never conduct any maintenance or make any other adjustments while the tractor
engine is running.

Always shut the tractor engine off, remove the ignition key, and keep the

engine off before carrying out any of the following procedures. Consult your tractor’s operator
manual for safe shutdown procedures to prevent accidental ignition.

•

Never

allow passengers to ride on the stump grinder.

WG24-MY2019: Rev A

Page of

7

28

22-Oct-2018

«
...
7
8
9
10
11
...
»

Содержание WG24

































Отзывы:

Нет отзывов

Похожие инструкции для WG24

Бренд: Parkside Performance Страницы: 107

Бренд: Milwaukee Страницы: 2

Бренд: Fein Страницы: 205

Бренд: Far Tools Страницы: 32

Бренд: Protool Страницы: 148

Бренд: Grizzly Страницы: 2

Бренд: emerio Страницы: 28

Бренд: Baratza Страницы: 11

Бренд: MIRKA Страницы: 124

Бренд: Yamato Страницы: 11

Бренд: Yamato Страницы: 13

Бренд: Yamato Страницы: 25

Бренд: XTline Страницы: 27

Бренд: CPS Страницы: 40

Бренд: Kobalt Страницы: 36

Бренд: Scheppach Страницы: 60

Бренд: Craftex Страницы: 17

Бренд: NorthStar Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды