Wood Stone FIRE DECK 6045 Скачать руководство пользователя страница 32

Страница: 32 / 44

Fire Deck

Service Manual

M0011.09 APRIL 2019

An ongoing program of product improvement may
require us to change specifications without notice.

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TOLL FREE

800.988.8103

TEL

360.650.1111

FAX

360.650.1166

E-MAIL

[email protected]

woodstone-corp.com

PARTS LIST

FIRE DECK SERIES OVENS

DESCRIPTION

PART NUMBER

Smart Valve SV-1, SV-2 or SV-3 - Natural Gas (NG)

7000-0750

Smart Valve SV-1, SV-2 or SV-3 - Propane (LP)

7000-0750 LP

Pilot / Igniter Assembly - Specify gas type

Call Wood Stone

Pilot Gasket (for Radiant Burner)

7000-0777

Pilot Tube (24" bare aluminum, no fittings)

RP-0051

Pilot Tube Compression Fitting

RP-7000-0251

Pilot Tube Union

7000-0260

Controller

7000-0099

RFG-IR Lexan Keypad Overlay

7000-0900

W-IR Lexan Keypad Overlay

7000-0901

RFG Lexan Keypad Overlay

7000-0902

Temperature Probe for 6045, 8645, 9660, 11260

7000-0727-8645

Temperature Probe for 9690

7000-0727-9690

Transformer

7000-0734

Pilot Orifice- Natural Gas (NG)

7000-0748-NG

Pilot Orifice- Propane (LP)

7000-0748

Conversion Kit for Smart Valve (to LP)

7000-0747

Conversion Kit for Smart Valve (to NG)

7000-0747-NG

Throttle (Flame Height) Control Valve - Natural Gas (NG)

7000-0183

Throttle (Flame Height) Control Valve - Propane (LP)

7000-0182

IR Burner Jet - Natural Gas (NG)

Call Wood Stone

IR Burner Jet - Propane (LP)

Call Wood Stone

Radiant Burner Jet for 8645 or 6045 (NG)

Call Wood Stone

Radiant Burner Jet for 8645 or 6045 Propane (LP)

Call Wood Stone

Radiant Burner Jet for 9690 - Natural Gas (NG)

Call Wood Stone

Radiant Burner Jet for 9690 - Propane (LP)

Call Wood Stone

Flame Retention Spring

RP-0017

Door Cable

5190-1316

Replacement Glass- 6045

4120-1001

Replacement Glass- 8645

4120-1001-1

Glass Gasket (specify model)

6100-0003

Содержание FIRE DECK 6045













































Результаты поиска

Содержание FIRE DECK 6045

Отзывы:

Похожие инструкции для FIRE DECK 6045

Бренды по названию

Популярные бренды

Wood Stone FIRE DECK 6045, Руководство по обслуживанию

Результаты поиска

Содержание FIRE DECK 6045

Отзывы:

Похожие инструкции для FIRE DECK 6045

Бренды по названию

Популярные бренды