wolke m600 basic Скачать руководство пользователя страница 36

Страница: 36 / 166

3-14 Installation of Printhead and Ink Cartridge

Rev AB

Wolke m600 touch Operator Manual

Installing the Printheads

Selection of a Suitable Installation Position

When arranging and positioning the printheads on the line, make sure
that it is possible to replace the cartridges at any time.

Warning

PERSONAL INJURY. Risk of injury to hands from moving machine
parts. When selecting the installation position, make sure that the
cartridges can be replaced at any time without any danger.

Note:

When planning the installation, please note that the optimum distance

between the nozzle plate on the cartridge and the print material is between 1 mm

and 3 mm (maximum). The head plate of the printhead can be directly in contact

with the product and is intended to provide protection for the cartridge.

Figure 3-26: Printing Head According to the Number of Printheads

Individual installation of

12.7 mm print height per

one printhead

printhead

Two printheads
Print height = 25.4 mm

Three printheads

Print height = 38.1 mm

Four printheads

Print height = 50.8 mm

Содержание m600 basic







































































































































































Результаты поиска

Содержание m600 basic

Отзывы:

Похожие инструкции для m600 basic

Бренды по названию

Популярные бренды

wolke m600 basic, Руководство оператора

Результаты поиска

Содержание m600 basic

Отзывы:

Похожие инструкции для m600 basic

Бренды по названию

Популярные бренды