12
R E M O T E B L O W E R
IMPORTANT NOTE:
Before turning
the power on, make sure the blower
is in the "OFF" position. Use wire con-
nectors or wire nuts approved by UL
or C/UL. Refer to installation instruc-
tions provided with each blower to
verify wall or roof cut-outs.
STEP 1: Plan the Installation
1)
Locate the blower so the length of
the duct run and number of elbows
and transitions are kept to a mini-
mum.
2)
Where possible, blower should be
located between wall studs or roof
rafters.
3)
Avoid pipes, wires or other duct-
work that may be running through
the wall.
4)
Be sure that there is enough space
for any transitions that may be need-
ed between the blower and the con-
necting ductwork.
5)
For best performance, locate tran-
sitions nearest the blower.
Feed 6” of ROMEX through the
knockout opening hole and into the
wiring box on the rough-in plate of
liner. Secure the cable to wiring box
with an appropriate connector.
Locate cord assembly provided with
the remote blower. The cord assem-
bly has two leads, black (L1) and
white (neutral). Connect these leads
to the leads from the blower, black to
black and white to white.
Connect ALL green and bare wires
together to the ground screw in the
wiring box.
4)
Plug cord assembly into receptacle
located near the center of the liner
shell. Use clips on liner interior to
keep excess power cord away from
moving parts.
5)
Re-install wiring box cover and
screws. Make sure all wires are secure
and that no wires are pinched
between cover and box.
STEP 2: Connect Remote Blower
NOTE:
Always refer to all blower
installation instructions provided with
the blower for additional mounting
and wiring instructions.
1)
Remove cover from wiring box
inside of liner shell. Remove wiring
box knockout.
2)
Feed 6” of inbound power cable
through the knockout opening hole
and into the wiring box. Secure the
cable to wiring box with an appropri-
ate connector for type of cable being
used.
Connect leads as follows:
•
Black (L1) to black (loose) in the
J box from the switch.
•
Neutral to neutral (loose) in the
J box from the switch.
3) Wiring Remote Blower:
Follow
wiring instructions at the blower as
outlined in the particular blower
installation instructions. Black (L1) to
black, white (neutral) to white – or
white to blue, or white to brown
(depending on model) and green to
grounding screw. Run remote blower
cable (ROMEX) to the liner.
Remote Blower Dimensions-600CFM
(801640) and 900CFM (801641)
24
1/2
"(622)
15
1/2
"(394)
28
1/4
"(717)
20
3/4
"(527)
24
3/4
"(629)
14"(356)
4
3/4
"(121)
10"(254)
DIAMETER
Remote Blower Dimensions-1200CFM
(801642)
Remote Blower Dimensions-1500CFM
(804701)
10"(254)
DIAMETER
14
3/4
"(375)
29
1/2
"(749)
29
1/2
"(749)
18"(457)
22"(559)
10
1/8
"(257)
7
1/4
"(184)
10"(254)
10"(254)
DIAMETER
14
3/4
"(375)
29
1/2
"(749)
29
1/2
"(749)
21"(533)
25"(635)
10
3/8
"(264)
7
1/4
"(181)
10"(254)
V
E N T I L A T O R
I
N S T A L L A T I O N