10
CHECK TIRE PRESSURE
The tires on your tractor were overinfl ated
at the factory for shipping purposes. Cor-
rect tire pressure is important for best
cutting performance.
• Reduce tire pressure to PSI shown in
“PRODUCT SPEC I FI CA TIONS” section
of this manual.
CHECK DECK LEVELNESS
For best cutting results, mower housing
should be properly leveled. See “TO LEV-
EL MOWER HOUSING” in the Service
and Adjustments section of this manual.
✔
CHECKLIST
Before you operate your new trac tor, we
wish to as sure that you re ceive the best
performance and sat is fac tion from this
quality product.
Please review the following checklist:
✓
All assembly instructions have been
com plet ed.
✓
No remaining loose parts in carton.
✓
Battery is properly prepared and
charged. (Minimum 1 hour at 6 amps).
✓
Seat is adjusted comfortably and tight-
ened securely.
✓
All tires are properly infl ated. (For ship-
ping purposes, the tires were over in -
fl ated at the factory).
✓
Be sure mower deck is properly lev eled
side-to-side/front-to-rear for best cutting
results. (Tires must be properly in fl at ed
for leveling).
✓
Check mower and drive belts. Be sure
they are routed prop er ly around pul leys
and inside all belt keepers.
✓
Check wiring. See that all connections
are still secure and wires are properly
clamped.
✓
Before driving tractor, be sure free wheel
control is in “transmission engaged”
position (see “TO TRANS PORT” in the
Operation section of this man u al).
While learning how to use your tractor, pay
extra attention to the following im por tant
items:
✓
Engine oil is at proper level.
✓
Fuel tank is fi lled with fresh, clean, reg-
u lar unleaded gas o line.
✓
Become familiar with all controls - their
location and func tion. Operate them
be fore you start the engine.
✓
Be sure brake system is in safe op er -
at ing condition.
✓
It is important to purge the trans mis sion
before op er at ing your tractor for the fi rst
time. Follow proper starting and trans-
mis sion purg ing instructions (See “TO
START EN GINE” and “PURGE TRANS-
MIS SION” in the Op er a tion sec tion of
this man u al).
CHECK FOR PROPER POSITION
OF ALL BELTS
See the fi gures that are shown for replac-
ing motion and mower blade drive belts
in the Service and Adjustments sec tion
of this manual. Verify that the belts are
routed cor rect ly.
CHECK BRAKE SYSTEM
After you learn how to operate your trac-
tor, check to see that the brake is properly
adjusted. See “TO ADJUST BRAKE” in
the Service and Adjustments section of
this manual.
Defl ector
Shield
Latch
Hooks
Mulcher
Plate
INSTALL MULCHER PLATE
NOTE:
If you installed the mulching blades
you will need to install the mulcher plate.
1. Raise and hold defl ector shield in
up right po si tion.
2. Place front of mulcher plate over front
of mower deck open ing and slide into
place, as shown.
3. Hook front latch into hole on front of
mower deck.
4. Hook rear latch into hole on back of
mower deck.
CAUTION:
Do not remove defl ector
shield from mower.
TO CONVERT TO BAGGING OR
DIS CHARG ING
NOTE:
The mulching blades will dis charge
and bag grass, but for best bagging and
discharging install the high per for mance
blades.
1. Remove mulcher plate and mulching
blades and install high performance
blades, (see BLADE REMOVAL in the
Maintenance section of this man u al).
2. Store mulching blades and mulcher
plate in a safe place. Your mower is
now ready for dis charg ing or in stal -
la tion of optional grass catcher ac-
ces so ry.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com
