manualshive.com logo in svg

WISKA VARITAIN PushIn, Руководство по эксплуатации

Поделиться
Скачать
WISKA VARITAIN PushIn Скачать руководство пользователя страница 9

50103430000_Varitain-PI(Ver1.4)Rev 01122018E.docx 

Repair and maintenance 

 

9 

4. Repair and maintenance 

5.1  Maintenance  

No maintenance is provided in addition to the regular checking of the contact sleeves 
(unavoidable wear caused by high numbers of plugging cycles and by dirty or faulty 
plugs). 

 

5.2  Repair 

Attention:    
The housing may not be opened when under voltage and only by 
trained staff. Safety measure to DIN VDE 0105 

 

 

Disconnect 

 

Shield unit from restart 

 

Verify disconnected parts are free of voltage 

 

Ground an by-pass 

 

Protect and separate the energised components near by. 

 
 

 

Repair / reconditioning work may only be undertaken using WISKA 
original spare parts. Changes or alterations to the equipment are not 
permitted. 

 

5.3   Replacement of the CEE-socket plug-in unit 

 

Precautionary measures   
Switch the entire equipment to the no-voltage state. Remove the cover 
and check whether the equipment has been switched to the no-voltage 
state with a voltmeter. Ensure that the equipment is not re-activated 
while working 

 
 

 

Содержание VARITAIN PushIn

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды