Wintriss Shadow VI Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 159

background image

1107200

Shadow VI User Manual

page 66

Chapter 2

Installation and Checkout

Final Checkout Sequence

DANGER

!

FAILURE TO PERFORM SAFETY SYSTEM TESTS

•

Perform the final checkout sequence below when you have completed installation of your

light curtain, before operating the equipment it is connected to.

•

Operate your machinery only after your safety system meets all the requirements of the

checkout sequence.

•

Perform the final checkout sequence whenever repair, maintenance or modification is

performed on your light curtain or the machinery it is connected to.

•

Perform the “daily test” safety system checkout sequence on page 93 (in French, en

Français, page 114) every day before operating any machinery connected to Shadow safety
light curtains.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

CHANGE IN STOPPING TIME REQUIRES SAFETY DISTANCE ADJUSTMENT

•

Repair your machinery stopping mechanism if its stopping time increases beyond the

acceptable limit.

•

Re-calculate the light curtain safety distance, using the new stopping time.

•

Adjust the location of the light curtain(s) accordingly.

•

Perform the checkout sequence before operating the equipment.

Failure to comply with these instructions will result in death or serious injury.

You have followed the installation steps in this chapter to correctly install your Shadow
safety light curtains. Now perform the checkout sequence to make sure your safety system is
working properly.

You must perform a checkout sequence after mounting and wiring are complete and before
you use Shadow safety light curtains with your machine.

It is also imperative to perform the checkout sequence every time any maintenance, repair or
other modification is performed on a Shadow safety light curtain unit or on the machinery
connected to the light curtain.

NOTICE

Use opaque test bars of 1 1/4" (32 mm) and 1/8” (3.2 mm) diameter for performing the

checkout sequence. If you are using the Floating Window option, also use a 2" diameter
test bar as instructed below.

Perform the daily test in Appendix A every day before operating the press. Follow the
checkout sequence below every time you repair, maintain or modify the press.

«
...
76
77
78
79
80
...
»

Содержание Shadow VI
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Shadow VI

Бренд: fantastic furniture Страницы: 10

Бренд: Habitat Страницы: 4

Бренд: Courtyard Creations Страницы: 4

Бренд: Courtyard Creations Страницы: 2

Бренд: Zanzini Страницы: 4

Бренд: HAMPTON BAY Страницы: 10

Бренд: Blanco Страницы: 2

Бренд: Bertini Страницы: 6

Бренд: Safety 1st Страницы: 19

Бренд: meubar Страницы: 16

Бренд: Smith Страницы: 16

Бренд: Safavieh Furniture Страницы: 2

Бренд: Parisot Meubles Страницы: 16

Бренд: Keter Страницы: 16

Бренд: HAMPTON BAY Страницы: 28

Бренд: Garage Tek Страницы: 4

Бренд: Osmond Ergonomics Страницы: 3

Бренд: MAISONS DU MONDE Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды