Wintex Agro 2000 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 17

background image

P A G E

|

15

Wintex Agro, Vilhelmsborgvej 8C, DK-7700 Thisted

+45 97990800, [email protected], www.wintexagro.com

17.

DISMOUNTING THE ACCUMULATOR

Loosen the screws carefully with a 4 mm hex key.

Note: There are two screws in each hole.

Use a 3 mm hex key.

18.

CONTROLLING THE ACCUMULATOR

Put a long rod down the hole the accumulator to check if the accumulator is

pressurized.

If the diaphragm can be pushed a lot, the accumulator must be charged with

Nitrogen or the diaphragm is defective.

In case of a defective diaphragm, the accumulator must be replaced

Loosen the charging screw with a 6 mm hex key.

If the accumulator is in order, you can hear a whistling sound of Nitrogen. In this
case merely recharge the accumulator.

If there is no whistling sound, the diaphragm is probably damaged and must be
replaced.

«
...
13
14
15
16
17
»

Содержание 2000


















Отзывы:

Нет отзывов

Похожие инструкции для 2000

Бренд: MRC Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды