manualshive.com logo in svg

WinGD X82-B, Руководство по обслуживанию

Поделиться
Скачать
WinGD X82-B Скачать руководство пользователя страница 675

Fig 11-28  Water separator - view 8

001

002

003

004

00452

8

Remove the lifting tool (003, 

Figure 11-28

) from the top of the water separator (004) and

attach it to the front of the water separator (004).

9

Operate the spur-geared chain block (001) to lift the water separator slightly.

10

Operate the lever chain hoist (005, 

Figure 11-27

) until the water separator (004, 

Figure

11-28

) is at the correct position.

11

Remove the lifting tool (003).

X82-B

AA00-6708-00AAA-720A-A

Maintenance Manual

Water separator - install

Winterthur Gas & Diesel Ltd.

- 675 -

Issue 001 2020-10

Содержание X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды