WinGD X62DF Скачать руководство пользователя страница 643

Страница: 643 / 902

Fig 11-11 Electric motor (free end) - install

001

002

003

004

005

006

007

008

009

010

011

008

00867

Electric motor - driving end

Step 2.1

Step 2.22

for the electric motor (006,

Figure 11-12

) at the driving end:

2.1

Attach the two slings (005) to the electric motor (006).

2.2

Attach the spur-geared chain block (004) to the trolley (003) and the two slings
(005).

2.3

Attach the shackle (001) to the lug.

2.4

Attach the spur-geared chain block (002) to the shackle (001).

2.5

Attach the shackle (008) to the strut as shown.

2.6

Attach the spur-geared chain block (007) to the shackle (008).

2.7

Attach the shackle (010) to the lug.

2.8

Attach the spur-geared chain block (009) to the shackle (010).

2.9

Operate the chain block (004) to lift the electric motor (006).

2.10

Move carefully the trolley (003) and electric motor (006) into position.

2.11

Attach the chain blocks (002, 009) to the two slings (005).

2.12

Operate the chain blocks (002, 004, 009) to move the electric motor (006) to the
middle position.

2.13

Carefully remove the chain block (004).

2.14

Attach the chain block (007) to the two slings (005).

2.15

Operate the chain block (007) to hold the weight of the electric motor (006).

2.16

Carefully remove the chain blocks (002, 009) from the two slings (005).

X72DF

AA00-6545-00AAA-720A-A

Maintenance Manual

Auxiliary blower - install

Winterthur Gas & Diesel Ltd.

- 643 -

Issue 002 2020-10

Содержание X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X62DF

Отзывы:

Похожие инструкции для X62DF

Бренды по названию

Популярные бренды

WinGD X62DF, Руководство по обслуживанию

Результаты поиска

Содержание X62DF

Отзывы:

Похожие инструкции для X62DF

Бренды по названию

Популярные бренды