background image

Maintenance

2722

1/A2

RT-flex58T-E

Winterthur Gas & Diesel Ltd.

 12/ 12

10. Protecting a nozzle tip

Remark:

 To protect the nozzle tip integrated in the injection valve against damage,

always fit protection cap 94271 for transport, storage, etc.

J

94271

11.

Storage and handling of injection valve

Store an injection valve in a dry place but not in a place contaminated with exhaust

gases or any other corrosive atmosphere. Keep the injection valve in its original

packing. Handle with care when preparing for use and avoid any hard contact

against other objects.

Attention!

 Do not open vacuum packed injection valve before the installation on

the engine.
For cleaning use white spirit, e.g. Shellsol TD, Shellsol T or Solvent FP68. Always

wear gloves and safety goggles with closed side frame!

2013

Injection Valve: Checking, Dismantling, Assembling and Adjusting

Injection Valve with FAST

Содержание WARTSILA RT-flex58T-E

























































































































































































































































































































































































































































































































Отзывы: