Apple and the Apple logo are trademarks of Apple Inc., registered
in the U.S. and other countries. App Store is a service mark of
Apple Inc., registered in the U.S. and other countries. Google Play
and the Google Play logo are trademarks of Google LLC. Winegard
is a registered trademark of Winegard Company. Disclaimer:
Although every effort has been made to ensure that the information
in this manual is correct and complete, no company shall be held
liable for any errors or omissions in this manual. Information provided
in this manual was accurate at time of printing. If the antenna does
not function as expected, please contact Winegard Co.
6) Install the included low band VHF element
assembly on the under side of the antenna
just above the mast clamp with the large
screw and a large flange nut. See Figure 4.
Unfold the elements until they lock into
place.
7) Insert the low band VHF element extensions
into the element sleeves, see Figure 1 for
location placement. Secure with the small
screws and small flange nuts. See Figure 5.
Attach to the rear VHF elements.
MOUNT ASSEMBLY
8) Find the end of the mounting pipe with
holes on the sides for screws. Insert this
end into the middle of the foot as shown.
9) Insert the 2 1/2" bolt through the foot and
pipe as shown. Screw a large flange nut
onto the end of the bolt to hold the pipe
and foot together.
Don’t tighten the nut
completely yet!
Figure 6.
10) Find the square holes on either side of the
bottom of the pipe. Raise the pipe slightly
and insert a 5/8" bolt through these holes
and out the side of the foot. Install the
large flange nuts on the outside of the foot
on the 5/8" bolts to hold the pipe in place.
Don’t tighten the nuts completely!
11) Secure the foot to it’s permanent
location. Adjust the end of the pipe so it
is perpendicular to the ground. Tighten the
hex nuts to hold the pipe in place.
ATTACHING ANTENNA TO MAST
12) Loosen U-bolt nuts. Slide U-bolt over
mast. Point small end of antenna toward
stations and tighten securely.
ANTENNA ASSEMBLY
For use on channels 7 – 51,
follow steps 1 through 5.
For use on channels 2 – 51,
complete steps 1 through 7.
1) Remove antenna and hardware
bag from carton. Unfold the tetrapoles and
the shorter VHF elements on underside of
the boom. Make sure they lock into place.
See Figure 1.
2) Insert the U-bolt into the mast clamp
insert and then into the mast clamp on the
antenna. Loosely thread 2 large flange nuts
onto the U-bolt. See Figure 2.
DO NOT TIGHTEN THE FLANGE NUTS
AT THIS POINT.
3) Install the matching transformer using two
small flange nuts and four washers from
the hardware bag. Make sure to place the
leads between two washers on each post.
Tighten the small flange nuts to secure the
leads. See Figure 3.
4) Flip the antenna over and unfold all of
the long VHF elements until they lock into
place. Be sure the elements are locked into
position and are flat and parallel to each
other. Unfold the UHF elements.
5) Insert the plastic end caps. Use a rubber
mallet to gently tap them into the antenna
booms to secure them.
Figure 5
After
Before
Top
Bottom
Holes to Align
Holes to Align
Figure 2
Large
Flange
Nuts
U-Bolt
Mast Clamp
Insert
Mast Clamp
Figure 3
Connecting the matching transformer.
Tetrapole
Figure 4
Figure 6
NOTE: If channels 2 – 6 are not
required,
skip steps 6 and 7.
Figure 1
Tetrapoles
VHF Elements
UHF
Elements
Mast Clamp
Matching
Transformer
Location
VHF Elements
Mast
Clamp
Attach Short
Extensions
Attach Long
Extensions
Leads
Post for Lead
Post for Lead
Low Band
VHF Element
Assembly
