Congratulations!
You have selected the Winegard
®
TRAV’LER Automatic Multi-Satellite TV Antenna. The TRAV’LER
antenna will deliver the ability to view both SHAW DIRECT satellites at the same time with unmatched
signal strength, the lowest travel height on the market, maximum HD capabilities and easy to use func-
tionality – just like you get at home. This manual provides important information on the installation and
operation of your TRAV’LER Interface Box. Please take time to read the manual in it’s entirety before
installing or operating your antenna.
Recommended Receivers:
The Winegard
®
TRAV’LER Automatic Multi-Satellite TV Antenna will work with any SHAW
DIRECT
™
receiver currently in production. Consult your receiver manual or www.winegard.com if you
have any questions about whether your receiver is compatible. However, we recommend:
SHAW DIRECT - DSR505 (HD capable)
DSR207 (SD only)
DVR530 (HD capable DVR)
Each receiver will require at least one coax cable. Refer to receiver manual for wiring details.
For information regarding Satellite coverage in North America, call Shaw Direct at 1-888-554-7827.
Before you begin, please make sure you have received all necessary parts to properly install and oper-
ate your TRAV’LER antenna.
- Installation and Operation Manuals
- Mount Base with 30’ Cable - Power/Control Cable
- TRAV’LER Interface Box
- Reflector, LNBF & Feed Arm (Packaged separately as the SKA-733)
- TRAV’LER Power supply with 24’ AC power cord
- Gray Coax Cable 30’
- Black Coax Cable 30’
- Mounting Hardware bag
- Cable Entry Hardware bag
Selecting a Location for the TRAV’LER Antenna
Before removing the TRAV’LER antenna from its box, check with your RV Dealer or manufacturer. Your
RV may be pre-wired or have a reinforced area for this system.
DO NOT install in a location where a
gap of 3/16” or more exists, as it may damage the roof. See diagram at top of page 3.
2
Icons appearing in the manual are used for important information and helpful tips.
Alert
indicates important information regarding
product use, product specifications or procedures.
Important tip
offers helpful suggestions or
refers you to a related topic in the manual.
INSTALLATION
Once you have checked for this:
1. Choose a location on the roof of the RV that will allow the dish to raise and rotate without interfer-
ence from other roof mounted equipment.
The TRAV’LER antenna may only be mounted parallel to
the centerline of the coach.
2. The minimum roof space required for the TRAV’LER antenna is 45.75” L x 36.91” W.
a.
The operational space requires that no obstructions taller than 6 inches be mounted within
a 70” diameter circle from the center of the unit.
3
You must find a location on the roof that provides adequate space to allow the TRAV’LER antenna to
operate. The TRAV’LER antenna has a Front and Back and must be mounted correctly to avoid dam-
age to the TRAV’LER antenna or the coach.
The antenna must be m/-5 degrees of level or
the system may require more time to locate the satellite(s).
The Transition plate for the TRAV’LER
unit is marked “FRONT” and “BACK”. See Figure 1.
FIGURE 1
FRONT OF R
V
TRANSITION
PLATE
Mount
Parallel to
Center Line
of Coach
!
Winegard is NOT liable for dam-
age, expenses, or injury caused
by improper installation.
3/16”
Plan your entire installation before
you start. Determine the location of
all of your equipment and make sure
cable and wires are long enough to
reach their destination points.
FRONT
BACK
INSTALLATION
When installing the TRAV’LER on a rubber roof, Winegard recommends using the SKA-004 Roller
Plate. If not using this plate, make sure that the roller does not come in contact with any rib supports
or bubbles in the roof when in operation. Failure to do so, may result in damage to the roof.
12.15
36.91
45.75
9.62
5.49
31.42
23.50
FIGURE 2
Mount Parallel to
Center Line of Coach
FRONT OF R
V
